CC BY
8
-□ □-
This paper reports the results of the experimental study to substantiate the rational structural and regime parameters of a two-drum reaping machine for harvesting flax oilseeds by the method of combing plants on the root. We have confirmed the results of the preliminary mathematical modeling of the process of separating a combed heap in the reaping machine with a predefined curved shape of the casing.
An experimental study of the heap separation process in a reaping machine has established the dependence of the mass fraction of the discharge of husk and stem particles from its region 8h, the proportion of the release of seeds and capsules with seeds 8h, and the consumed power P, on the rotation frequency of the beater-reflector ni, and the combing drum n2, the position of the air grate L and its width B. The following structural-mode parameters of the comb-type reaping machine for harvesting oil flax seeds have been defined as the most significant ones: the rotation frequency of the beater-reflector, n1=892 rpm; the rotation frequency of the comb drum, n2=652 rpm; the position of the air grate, L=0.62 m, and its width, B=0.56 m. In this case, the mass fraction of the discharge of husk and stem particles is 8h=47.5 %, the share of the loss of seeds and capsules with seeds from the reaping machine is, respectively, 8h=2.1 %, and the power consumed to perform the process is P=2.7 kW.
The statistical analysis has demonstrated that the correlation coefficient between the theoretical and experimental data is 0.88-0.95; a relative error in the optimal values is 4.6 %. The actual and statistical comparison of the theoretical and experimental data has confirmed the adequacy of the mathematical models built as a result of the theoretical research.
Based on the results of our experimental research, one can argue about the usefulness of their application for engineering calculations when designing new technical means for harvesting crops by the method of combing plants on the root
Keywords: combing reaping machine, technology of combing plants on the root, oil
flax, optimal structural-mode parameters -□ □-
UDC 631.17; 633.1
|DOI: 10.15587/1729-4061.2020.212733|
EXPERIMENTAL SUBSTANTIATION OF THE RATIONAL PARAMETERS FOR A REAPING MACHINE OF THE COMB TYPE FOR HARVESTING OIL FLAX
SEEDS
О. Kozachenko
Doctor of Technical Sciences, Professor* E-mail: o.v.kozachenko21@gmail.com A. Pakhuchyi PhD, Senior Lecturer** Е-mail: andreyi09773@gmail.com O. S h kreg al PhD, Associate Professor* E-mail: shkregall@ukr.net S. Soroki n PhD, Associate Professor* E-mail: sorokinsp@ukr.net S. Dyakonov PhD, Associate Professor** Е-mail: dsa1977oct@gmail.com N. Gusarenko PhD, Associate Professor** Е-mail: gusarenco453@gmail.com V. Kadenko PhD*
E-mail: volodymyr_kadenko@ukr.net *Department of Reliability, Durability and Technical Service of Machines named after V. Ya. Anilovich
Kharkiv Petro Vasylenko National Technical University of Agriculture Alchevskykh str., 44, Kharkiv, Ukraine, 61002 **Department of Technical Support of Agricultural Production Kharkiv national agrarian University named after V. V. Dokuchaev p/o «Dokuchaevske-2», Kharkiv dist., Kharkiv reg., Ukraine, 62483
Received date 04.04.2020 Copyright © 2020, C. Kozachenko, A. Pakhuchyi,
Accepted date 23.09.2020 O. Shkregal, S. Sorokin, S. Dyakonov, N. Gusarenko, V. Kadenko
Published date 13.10.2020 This is an open access article under the CC BY license (http://creativecommons.org/licenses/by/4.0)
1. Introduction
The process of harvesting crops, including oil flax, is an important technological operation of their production in the agricultural sector. The positive dynamics of the growth of
oil flax production, due to the growing demand for seeds in the domestic and foreign markets, requires the intensification of technological processes in harvesting equipment.
One of the promising directions of the intensification of technical means for harvesting oil flax is the technology
of harvesting by the method of combing plants on the root. At the same time, timely harvesting of oil flax in optimal agro-technical terms at minimal losses and contamination of the combed heap is one of the most important scientific tasks of improving harvesting equipment. The main feature of a given promising harvesting technology is a significant reduction in the non-grain share in the combed heap compared to the grain-stem mass entering the threshing-separating working bodies in conventional grain harvesters. This leads to the need to improve quality, productivity, and to reduce the energy intensity of the technological harvesting process [1-3]. In this case, the structural and technological parameters of the working bodies, the mode of operation of harvesting machines, as well as the physical-mechanical properties of agricultural crops, exert a significant impact on the effectiveness of the harvesting process [4-6]. The issues relating to using standard reaping machines of the comb type for harvesting include a large variety of agricultural crops, differences in the physical and mechanical properties of plants, structural imperfections, the levels of development of the combing process theory and the design of effective schemes of technical means.
When designing a combing device for harvesting oil flax seeds, an important task is the choice of the rational structural and mode parameters that can minimize seed losses during the process. Therefore, the directions of the scientific search for new technical solutions and technological processes of harvesting should provide for the theoretical aspect of studying the problem and for the practical confirmation of mathematical models built.
The relevance of this work is predetermined by the need to clarify and supplement the theoretical provisions formulated by us in an earlier study of the process of harvesting flax seeds using the method of plant combing.
2. Literature review and problem statement
The comparative analysis [7] of single- and double-drum combing devices proved the advantage of the latter in the process of harvesting by the method of combing plants on the root. The main provisions of the theory of combing of agricultural crops and the development of two-drum structures of technical means for the implementation of the specified process were proposed in works [8, 9]. However, the constructed mathematical models do not provide a comprehensive approach to considering the process of interaction between plants and the working bodies of a combing two-drum reaping machine. The authors did not fully take into consideration the influence of the physical and mechanical properties of plants on the shape formation of the device's fairing. The influence of related processes was disregarded, in particular, an airflow that separates the components of the combed heap and the shape of the reaping machine's casing. Mathematical expressions are complicated or are impractical for the further practical use in order to build new effective technical means for harvesting by the method of combing plants on the root.
A promising direction in the technology development and technical support to the process of combing plants on the root with a two-drum reaping machine can be a comprehensive approach to its implementation. This primarily applies to taking into consideration the properties of the harvested object, the sequence of its interaction with the working bodies of the device, the structural-mode parameters of the reaping machine, and the parameters of the related processes in its area.
This very approach was implemented in works [10-14]. Theoretical studies have established the effect exerted on the process of harvesting oil flax by the developed reaping machine of the comb type by the structural and regime parameters, plant properties, and the components of the combed heap. When building mathematical models, the authors also took into consideration the influence of the accompanying processes that occur in the region of a reaping machine in the implementation of the harvesting process.
When studying processes related to a combing reaping machine, the authors used the following as the physical models for numerical modeling: a k-£ model of the turbulence of the combined current, a field of gravity, the real gas model by Van der Waals, the Navier-Stokes equation averaged by Reynolds equation [15, 16]. The air current was examined using the STAR-CCM+software package, implemented on the basis of a finite-element method [17, 18]. The mathematical models built by the authors involve a comprehensive approach to the process of combing plants on the root by a two-drum reaping machine. They imply calculations in accordance with the sequence of the implementation of the process of interaction between an object (plant stems, the components of the combed heap), and the working bodies of a reaping machine. In this case, the initial parameters of the object are taken into consideration when interacting with the preceding working body of the combing reaping machine. The same consideration applies to the interacting with all subsequent working bodies of the reaping machine. Based on the results of a theoretical study into the process of bending the plant of oil flax under the influence of the reaping machine's fairing, based on the theory of elasticity, the authors of work [10] derived the equation of its shape. The equation is given in the cartesian coordinate system in the form of a second-degree polynomial depending on the bio-metric parameters of plants and the density of their standing. The resulting shape of the fairing contributes to driving the vegetable mass of the crop to a «state of combing» by tilting the plants forward towards the movement of the reaping machine. This makes it possible to compensate for the tiering of the plant and prepares the stem mass for the next stage of the process-contact with the combing drum.
In works [11, 12], the authors theoretically investigated the process of fluctuations in the plant of oil flax after the interaction with a reaping machine's fairing, assuming the execution of fluctuations in one of the main planes of the plant stem and taking into consideration their biometric characteristics. Based on the results of mathematical modeling of the process of the interaction of a plant with the combing drum, and on the basis of the theory of fluctuations, the authors derived a dynamic function of changing the curvature of the stem depending on its rheological properties. They defined the structural parameters of a reaping machine's drum, which ensure the effective implementation of the process of combing plants.
In another study [13], the authors analytically examined the process of interaction between the unrelated particles of the components of a combed heap of oil flax and the comb of a reaping machine's drum. Based on the laws of dynamics, they solved the differential equation of their movement on the surface of the comb and established the dependence of their overall speed on the rotation frequency of the comb drum. The differential equation suggested in the cited study was used to analyze the movement of the components of a combed heap over the surface of the comb of the device depending on the mode parameters of the comb drum of the
..J53
reaping machine. A theoretical study reported in [14] established the impact of the structural and regime parameters on the formation of airflow and maximum speed in its area, which led to the determining the rational shape of the casing and the position of the air grate for the discharge of light impurities. In the numerical modeling of the processes of the separation of the components of a combed heap in the region of a reaping machine with the curved shape of the casing, the authors took into consideration their physical and mechanical properties. They theoretically defined the significant factors of influence on the process: the rotation frequency of the beater-reflector n and the combing drum n2, the position of the transparent area of the border L of the air grate of the casing and its width B.
The authors solved a compromise problem on maximizing the share of the discharge of impurities 8h and minimizing the loss of seeds and seed capsules 8S. They theoretically defined the following rational structural-mode parameters of a combing reaping machine: the rotation frequency of the beater-reflector, n1 = 782 rpm; the rotation frequency of the comb drum, n2 = 671 rpm; the position of the transparent zone of boundaries, L = 0.82 m, and its width, B = 0.45 m.
Given the results of the analysis reported in works [10-15], based on the technological parameters of the harvester operation, the influence of the structural and regime parameters of a reaping machine and the physical and mechanical properties of the stem mass, as well as an oil flax heap, there is reason to consider it appropriate to conduct experimental research into the rational parameters of the combing reaping machine for harvesting oil flax seeds.
This could confirm and supplement the mathematical models of the harvesting process based on the method of combing plants on the root that we have earlier built and apply them when constructing new effective technical means.
3. The aim and objectives of the study
The aim of this work is to experimentally substantiate the structural-mode parameters for a two-drum reaping machine of the comb type for harvesting oil flax seeds. This would provide an opportunity to design more effective technical means for harvesting by the method of combing plants on the root.
To achieve the set aim, the following tasks have been solved:
- to devise a methodology and technical support to perform an experimental study of the process of harvesting oil flax seeds using a two-drum combing reaping machine;
- to experimentally determine the rational parameters for a reaping machine of the comb type for harvesting oil
flax seeds that would provide for a decrease in the amount of losses in the execution of the process.
4. Experimental substantiation of the rational parameters for a combing reaping machine for harvesting oil flax
4. 1. Methodology and technical support of the study
An experimental laboratory installation [19] was designed to study the technological process of plant combing and to define the rational parameters for a reaping machine of the comb type for harvesting oil flax seeds. The structural-technological scheme and the physical appearance of the designed experimental installation for combing plants are shown in Fig. 1.
In the operational process of the experimental installation, the plants of oil flax are primarily in contact with fairing 1, which contributes to driving them to the «state of combing» by tilting the plants forward in the direction of movement, which makes it possible to compensate for the tiering of the plants and prepares the stem mass for the next stage -a contact with comb drum 3. The simulation of the installation movement in the direction of rows of oil flax plants is carried out by means of moving field 15 whose speed can be chosen in accordance with the working speeds of the machine. After coming off the outer surface of fairing 1, plants enter the combing area, where they come into contact with comb drum 3. The components of the combed heap (seeds, capsules with seeds, husks of capsules, slices of stems, dust impurities), under the influence of the inertia and airflow forces formed by beater-reflector 2 and comb drum 3, are moved along the transporting channel to the zone of tray 6. Small particles of heap and dust are discharged out of the installation through air grate 5. The components of the combed heap are collected in tray 6, the target fraction, and tray 14, losses in the operation of the combing device.
The height of plants relative to the location of the fairing is set by clamps in the moving field (Fig. 2, a). The rotation frequency of beater-reflector 2 and comb drum 3 is changed by changing the gear ratio of the drive by selecting the drive sprockets with a different number of teeth. One installation's wall is transparent, which allowed us to perform visual observation of the process and record a video. The visualization of the trajectories of the movements of the components of the combed heap (Fig. 2, b) helped establish that the particles of stems, husks, and dust fractions have a more inclined motion trajectory compared to the oil flax seeds and capsules with seeds, causing their segregation and removal of the lighter and smaller components through the air grate of casing 5.
a
b
Fig. 1. Laboratory installation to study the parameters and modes of the agricultural crop combing process [18]: a — structural scheme; b — physical appearance; 1 — fairing; 2 — beater-reflector; 3 — comb drum; 4 — upper casing; 5 — air grate; 6 — tray for discharging combed heap; 7 — control panel; 8 — frame; 9 — flexible cable; 10 — drum; 11 — gearbox; 12 — electric motor; 13 — guides of the moving field; 14 — loss sampling tray; 15 — movable field
Fig. 2. Preparation of plants and the process of moving heap components in the transporting channel: a — the preparation of plants for combing; b — the visualization of the movement of the components of the combed heap: 1 — target fraction (seeds and capsules with seeds); 2 — non-target fraction (the discharge of husk and stem particles)
Careful observation of the process of simulating the combing of plants at the experimental installation has allowed us to better evaluate the process of harvesting plants based on the specified method.
We studied the process of harvesting oil flax seeds at the laboratory installation for combing plants based on four factors: the rotation frequency of the beater-reflector n1 and the comb drum n2, the position of the air grate L, the width of the air grate B. The factors' variance ranges and levels are given in Table 1.
Table 1
The variance levels of factors in experimental research
Factor variance level Factor
The beater-reflector rotation frequency n1, rpm (x1) The comb drum rotation frequency «2, rpm (X2) The air grate position L, m (X3) The air grate width B, m (x4)
Upper level (+) 960 920 1 0.6
Basic level (0) 780 670 0.8 0.4
Lower level (-) 600 180 0.6 0.2
Factor variance interval 180 250 0.2 0.2
Our experimental study employed the D-optimal Box-Ben-kin plan of the second order for 4 factors with a total number of experiments of 27; repeated three times.
In determining the composition of the components and their quantitative characteristics, we separated from the combed heap the oil flax seeds combed by the combs of the drum at the experimental installation, the uncombed capsules with seeds, the husks of capsules, and the particles of plant stems. The physical appearance of the components of the combed heap of oil flax is shown in Fig. 3.
a b c d
Fig. 3. The physical appearance of the components of the combed heap of oil flax: a — seeds; b — capsules with seeds; c — husks; d — stem particles
The following criteria for assessing the process of the separation of a heap in a reaping machine of the comb type were adopted: the mass fraction of the discharge of husks and stem particles from the reaping machine's region 8h, the mass fraction of the discharge of seeds and capsules with seeds from the region of the reaping machine 8s. In addition, a process evaluation criterion was the average power P consumed by the experimental installation. The average power P was determined, using an electric meter, as the ratio of consumed electricity to the time of installation operation when combing plants.
4. 2. Results of the experimental substantiation of the rational parameters for a combing reaping machine for harvesting oil flax
To determine the rational structural-mode parameters for a reaping machine of the comb type, we shall solve a compromise problem. The optimization problem, in this case, is reduced to maximizing the mass fraction of the discharge of husk and stem particles from the region of the reaping machine 8h and minimizing the share of the discharge of seeds and capsules with seeds from the region of the reaping machine 8s which causes the loss of the target fraction when harvesting.
During the study, we calculated, for each experiment, the mass fraction of the discharge of husk and stem particles from the region of the reaping machine 8h, and, using the Wolfram Mathematica software package, performed the approximation of data obtained, the result being the dependence on the study factors in the encoded form:
8h = 41.5584 +164,012^ + 0.886248x* - 6.31347x2 -- 1.00102xjx2 -1.76295x2 + 3.39003x3 +
+ 0.534828xtx3 + 0.146541x2x3 - 1.34309x32 +
+ 8.52373x4 +1.48706xtx4 - 2.7061x2x4 -
- 0.387163x3x4 + 0.389504x42.
(1)
The statistical treatment of the resulting equation (1) is consolidated in Table 2. An analysis of Table 2 makes it possible to reduce the insignificant coefficients in equation (1) and represent it in a decoded form:
8h = 17.6018 + 60.7155B + 9.73761B2 + 62.9574L -- 9.67908BL - 33.5772L2 - 0.0412674nt + + 0.0413073Bn + 0.0148563Ln + 0.0000273533n? +
+ 0.0920035n2 - 0.0751693B« -- 0.0000308956n1n2 - 0.000054412n22
Table 2
Statistical treatment of equation (1)
Coefficient Standard error t - Student criterion Error probability at deviation
«00 0.473608 87.7486 3.0886440-91
«10 0.236804 6.92607 5.5227640-10
«20 0.236804 -26.6612 2.4391940-45
«30 0.236804 14.3157 3.0419940-25
«40 0.236804 35.9949 2.1648240-56
«12 0.410157 -2.44058 0.0165579
«13 0.410157 1.30396 0.195465
«14 0.410157 3.6256 0.00047027
«23 0.410157 0.35728 0.721692
«24 0.410157 -6.59771 2.522640-9
«34 0.410157 -0.94394 0.347646
«11 0.355206 2.49503 0.0143585
«22 0.355206 -4.96317 3.1263840-6
«33 0.355206 -3.78116 0.000275684
«44 0.355206 1.09656 0.275666
Taking into consideration the maximization of the mass fraction of the discharge of husk and stem particles from the reaping machine's region 8/, we obtain the rational parameters in the first approximation:
=64.9 %, n1 = 960 rpm, n2=490 rpm, L = 1 m, B=0.6 m.
(3)
By alternately registering the research factors at a certain level according to (3), the graphical interpretations of dependence (2) are constructed in Fig. 4.
rpm
900 b
500
Fig. 4. Dependence of the mass fraction of the discharge of husk and stem particles from the region of the reaping machine 8h on: a — the rotation frequency of the beater-reflector n and the comb drum n2; b — the position of the air grate B and its width L at the fixed values of (3)
Fig. 4 shows that with an increase in the rotation frequency n1, the position L, and the width B of the air grate, the mass fraction of the discharge 8S increases. In turn, with the increase in the rotation frequency n2, the mass fraction of the discharge 8/, decreases.
For each variant of the experiment, we calculated the mass fraction of the discharge of seeds and capsules with seeds from the region of the reaping machine 8S, and, using the Wolfram Mathematica software package, performed the approximation of data obtained, the resulting being the dependence on the study factors in the encoded form:
8 h = 3.97364 - 1.283x1 + 1.13561x2 + 4.10254 x2 -
- 0.246487x1x2 + 8.6198x22 + 0.61405x3 +
+ 0.167918^ - 0.000607501x2x3 -
- 0.0987031x2 - 1.32029x4 - 1.2141x1x4 -
- 2.0635x2x4 -0.158931x3x4 + 0.0344613x42. (4)
The statistical treatment of the resulting equation (4) is consolidated in Table 3. An analysis of Table 3 makes it possible to reduce the insignificant coefficients in equation (4) and represent it in a decoded form:
8 h = 105.398 + 61.2868B+4.96947L - 3.97328BL -
- 2.46758L2 -0.0469495n1 -0.033725Bn1 +
+ 0.00466438Ln1 + 0.0000350496n2 - 0.304844n2 -
- 0.0573195Bn2 - 7.60763 ■ 10-6n1n2 + 0.000266243n22. (5)
Table 3
Statistical treatment of equation (4)
Coefficient Standard error t - Student criterion Error probability at deviation
«00 0.174558 22.7619 8.54305-10-40
«10 0.087279 -14.7007 5.4518740-26
«20 0.087279 47.0073 1.3057240-66
«30 0.087279 7.03639 3.299440-10
«40 0.087279 -15.1256 8.34494-10-27
«12 0.151172 -1.63073 0.106328
«13 0.151172 1.11132 0.269296
«14 0.151172 -8.03006 2.9328840-12
«23 0.151172 -0.00325929 0.997406
«24 0.151172 -13.6517 6.1573540-24
«34 0.151172 -1.0533 0.294933
«11 0.130919 8.67205 1.314840-13
«22 0.130919 65.84 8.07732-10-80
«33 0.130919 -0.752059 0.453915
«44 0.130919 0.262781 0.793301
Taking into consideration the minimization of the mass fraction of the discharge of seeds and capsules with seeds from the region of the reaping machine 8S, we obtain the rational parameters in the first approximation:
Ss=0.47 %, n1=960 rpm,
n2=651 rpm, L=0.6 m, B=0.6 m.
(6)
By alternately registering the study factors at a certain level according to (6), the graphical interpretations of dependence (5) are constructed in Fig. 5.
S„%
Table 4
1.0 0.2
a
800
700 600 n,, rpm
900 b
Fig. 5. Dependence of the mass fraction of the discharge of seeds and seed capsules from the region of the reaping machine 8S on: a — the rotation frequency of the beater-reflector n1 and the comb drum n2; b — the position of
the air grate B and its width L at the fixed values of (6)
Fig. 5 shows that with an increase in the rotation frequency n1 and the width of the air grate B, and with a decrease in the value of the position of the air grate L, the mass fraction of the discharge 8s decreases. In turn, for the rotation frequency n2 there is an optimum (n2 = 651 rpm), at which the mass fraction of the discharge 8s is minimal within the assigned range of factors.
This makes it possible to assert the high-quality progress of the technological process of combing the plants of oil flax at the minimal discharge of the target fraction from the region of the reaping machine.
For each variant of the experiment, we determined the average power consumed by the installation P, and, using the Wolfram Mathematica software package, performed the approximation of data obtained, the result being the dependence on the study factors in the coded form:
P = 2.90832 + 0.144157x1 - 0.0578619x2 +
+ 0.289464x2 - 0.05x4x2 - 0.0828869x22 -
- 0.0125x3 + 6.59195 10-17 x4x3 - 0.04375x2x3 -
- 0.0583333x32 -0.229583x4 -0.0125x4x4 -
- 0.0375x2x4 - 0.00625x3x4 - 0.00520833x42. (7)
The statistical treatment of the resulting equation (7) is consolidated in Table 4.
An analysis of Table 4 makes it possible to reduce the insignificant coefficients in equation (7) and represent it in a decoded form:
P = -3.23992 - 0.45B + 3.14757L -1.45833L2 +
+ 0.00462077^ -1.78586 ■ 10-6 nj2 +
+ 0.00762877n2 - 0.00104167Bn2 -
- 0.00121528Ln2 -1.54321 10-6 n« -
- 2.55824 10-6n22.
Statistical treatment of equation (7)
Coefficient Standard error t - Student criterion Error probability at deviation
a00 0.043587 66.7245 2.3951240-80
ai0 0.0217935 6.61468 2.3334540-9
a20 0.0217935 13.2821 3.3568910-23
a30 0.0217935 -0.573565 0.567646
a40 0.0217935 -10.5345 1.5277540-17
ai2 0.0377475 -1.32459 0.188552
ai3 0.0377475 1.74633-10-15 1
ai4 0.0377475 -0.331148 0.741278
a23 0.0377475 -1.15902 0.249416
a24 0.0377475 -0.993444 0.323071
a34 0.0377475 -0.165574 0.868852
aii 0.0326903 -1.77 0.0800038
a22 0.0326903 -2.53552 0.0128964
a33 0.0326903 -1.78443 0.0776156
a44 0.0326903 -0.159324 0.873759
Taking into consideration the minimization of the average power consumed by the installation P, we obtain the rational parameters in the first approximation:
P = 1.98 W, n1 = 600 rpm,
n2 = 490 rpm, L=0.6 m, B=0.6 m.
(9)
By alternately registering the study factors at a certain level according to (9), the graphical interpretations of dependence (8) are constructed in Fig. 6.
P, kW
800
rpm
900 a
500
1.0 0.2
b
Fig. 6. Dependence of the average power consumed by the installation P on: a — the beater-reflector's rotation frequency n and the comb drum's rotation frequency n2; b — the position of the air grate B and its width L at the fixed values of (9)
Fig. 6 shows that with an increase in the rotation frequency n and n2, and with a decrease in the width of the air grate B, the average power consumed by the installation P
increases. In turn, the position of the air grate L has virtually no effect on the specified study criterion.
When solving a compromise problem, namely, maximizing the mass fraction of the discharge of husk and stem particles from the region of the reaping machine S,, minimizing the proportion of the discharge of seeds and capsules with seeds from the region of the reaping machine Ss and minimizing the consumed power P, we have obtained the rational structural-technological parameters for a combing reaping machine: the rotation frequency of the beater-reflector, n=892 rpm; the rotation frequency of the comb drum, n2=652 rpm; the air grate position, L=0.62 m; and it width, .8=0.56 m. At the same time, the mass fraction of the discharge of husk and stem particles from the region of the reaping machine is S,=47.5 %, the share of the discharge of seeds and capsules with seeds from the reaping machine's region is, respectively, Ss = 2.1 %, and the power consumed by the experimental installation is P= 2.7 kW.
Thus, the experimentally obtained rational values for the structural-mode parameters of a combing reaping machine ensure the high-quality implementation of the process of combing oil flax plants at the minimal losses of the target fraction in the form of seeds and capsules with seeds Ss and the maximum removal of mechanical impurities in the form of husks of capsules and stem particles S/ from the region of the reaping machine.
Thus, the results of our study indicate the dependence of the operational quality of a two-drum combing reaping machine on its structural-mode parameters. Namely: the rotation frequency of the beater-reflector n1 = 892 rpm, the rotation frequency of the comb drum n2=652 rpm, the position of the air grate L=0.62 m, and its width B=0.56 m. In this case, the mass fraction of the discharge of husk and stem particles from the reaping machine's region is S/ = 47.5 %, the share of the discharge of seeds and capsules with seeds from
the reaping machine's region is, respectively, Ss = 2.1 ' the power consumed by the installation is P = 2.7 kW.
and
b
Fig
7. Dependence of the mass fraction of the discharge of husk and stem particles from the region of the reaping machine Sh on: a — the rotation frequency of the beater-reflector n1 and the comb drum n2; b — the position of the air grate L and its width B; 1 — theoretical; 2 — experimental
5. Discussion of results of experimental substantiation of epy rational parameters for a two-drum combing reaping machine for harvesting oil flax
800
rpm
The qualitative performance of a two-drum reaping machine of the comb type is significant affected by its structural-mode parameters.
The results of our experimental study confirm basic theoretical provisions formulated by us in [10-14] regarding the impact exerted on the mass fraction of the discharge of husk and stem particles from the region of the reaping machine S/, the mass fraction of the discharge of seeds and capsules with seeds from the region of the reaping machine Ss.
The statistical analysis has shown that the correlation coefficient between the theoretical and experimental data is 0.88-0.95, and the relative error in the optimal parameter values is 4.6 %. The actual (Fig. 7, 8) and statistical comparison of the theoretical and experimental data allows us to assert the adequacy of the mathematical models obtained, which are developed as a result of earlier theoretical research. This makes it possible to apply the results of our study when designing new effective combing devices.
.0 0.2
ab
Fig. 8. Dependence of the mass fraction of the discharge of seeds and seed capsules from the region of the reaping machine Sh on: a — the rotation frequency of the beater-reflector n1 and the comb drum n2; b — the position of the air grate L and its width B; 1 — theoretical; 2 — experimental
The above allows us to draw a conclusion about the quality of the developed mathematical model of the process and the effectiveness of its application in the construction of technical means for harvesting crops by the method of combing plants on the root. That predetermines the possibility of their use for engineering calculations when designing new effective combing devices for harvesting crops.
6. Conclusions
1. We have devised the methodology and technical support for the experimental research into the process of harvesting oil flax seeds with a two-drum combing reaping machine; the dependence of the mass fraction of the discharge of impurities S/, seeds Ss, and the consumed power P on the rotation frequency of the beater-reflector n1 and the comb drum n2 in
a two-drum reaping machine, the position of the casing's air grate L, and its width B has been experimentally established.
2. Solving the compromise problem on maximizing the mass share of the discharge of impurities 8h, minimizing the loss of seeds 8s, as well as consumed power P, produced the rational parameters for the reaping machine. These parameters are: the rotation frequency of the beater-reflector n1 = 892 rpm, the rotation frequency of the comb drum n2 = 652 rpm, the position of the air grate L=0.62 m, and its width B = 0.56 m. In this case, the mass fraction of
the discharge of husks and stem particles from the reaping machine's region is 8h=47.5 %, the share of the discharge of seeds and capsules with seeds from the reaping machine's region is, respectively, 8s=2.1 %, and the power consumed by the installation is P = 2.7 kW. At the same time, the correlation coefficient between the theoretical and experimental data is 0.88-0.95, the relative error in the optimal values is 4.6 %. The actual and statistical comparison of the theoretical and experimental data allows us to assert the adequacy of the developed mathematical models.
References
1. Kushnarev, A. Kravchuk, V., Lezhenkin, A. (2010). Problemy sovershenstvovaniya tehnologii uborki zernovyh. Tekhnika i tekhnolo-hiyi APK, 2, 6-12.
2. Sysolin, P. V., Ivanenko, I. (2008). Problemy i perspektivy vnedreniya v Ukraine tehnologii uborki zernovyh kolosovyh kul'tur metodom ochesyvaniya koloskov. Tehnika APK, 5, 24-29.
3. Lezhenkin, A. N., Kravchuk, V. I., Kushnarev, A. S. (2010). Tehnologiya uborki zernovyh metodom ochesa rasteniy na kornyu: sostoyanie i perspektivy. Bila Tserkva, 400.
4. Yuan, J., Lan, Y. (2007). Development of an Improved Cereal Stripping Harvester. Agricultural Engineering International: the CIGR Ejournal, IX. Available at: http://citeseerx.ist.psu.edu/viewdoc/download7doi = 10.1.1.504.7187&rep=rep1&type=pdf
5. Chekhov, A. V., Lapa, O. M., Mishchenko, L. Yu., Poliakova, I. O. (2007). Lon oliynyi: biolohiya, sorty, tekhnolohiya vyroshchu-vannia. Kyiv: Ukrainska akademiya ahrarnykh nauk, Instytut oliynykh kultur, 59.
6. Sai, V. A. (2012). Tekhnolohiya vyroshchuvannia, zbyrannia ta pervynnoi pererobky lonu oliynoho. Lutsk: LNTU, 166.
7. Shabanov, P. A., Shabanov, N. P. (2004). Sravnitel'nyy analiz odno- i dvuhbarabannyh ochesyvayushchih ustroystv na uborke zernovyh kul'tur. Nauchnye trudy Ukrainskogo tsentra ispytaniy tehniki (UKRTSIT). Doslidnitskoe, 173.
8. Shabanov, P. A., Shabanov, N. P. (2006). Obmolot na kornyu - dal'neyshee razvitie dvuhfaznogo sposoba obmolota zernovyh kul'tur. Dostizheniya nauki i tehniki APK, 8, 8-10.
9. Golubev, I. K., Goncharov, B. I., Shabanov, P. A. (1986). Obmolot risa na kornyu dvuhbarabannym ochesyvayushchim ustroystvom. Traktory i sel'skohozyaystvennye mashiny, 2, 35-38.
10. Kozachenko, O. V., Diakonov, S. O., Pakhuchyi, A. M. (2018). Obgruntuvannia formy obtikacha obchisuvalnoi zhnyvarky dlia zbyrannia lonu oliinoho. Mekhanizatsiya ta avtomatyzatsiya vyrobnychykh protsesiv, 5 (33), 48-52.
11. Kozachenko, O. V., Diakonov, S. O., Honcharov, V. V., Pakhuchyi, A. M. (2019). Doslidzhennia rezhymnykh parametriv obchisu-valnoho barabanu zhnyvarky. Visnyk Kharkivskoho natsionalnoho tekhnichnoho universytetu silskoho hospodarstva imeni Petra Vasylenka, 199, 388-396.
12. Kozachenko, O., Pahuchiy, A. (2019). Modeling of interaction with plants linseed occupancy drum. TEKA. An International Quarterly Journal on Motorization, Vehicle Operation, Energy Efficiency and Mechanical Engineering. Lublin-Rzeszow, 19 (1), 59-64.
13. Kozachenko, O. V., Pakhuchy, A. M., Dyakonov, S. O., Goncharo, V. V. (2019). Substantiation of structural and technological parameters of the reeling drum. Engineering of nature management, 1 (11), 74-82.
14. Kozachenko, O., Pakhuchyi, A., Shkregal, O., Dyakonov, S., Blaznyuk, O., Kadenko, V. (2019). Results of numerical modeling of the process of harvesting the seeds of flax by a harvester of the stripping type. Eastern-European Journal of Enterprise Technologies, 3 (1 (99)), 66-74. doi: https://doi.org/10.15587/1729-4061.2019.169664
15. Bai, C., Gosman, A. D. (1995). Development of Methodology for Spray Impingement Simulation. SAE Technical Paper Series. doi: https://doi.org/10.4271/950283
16. Wallin, S. (2000). Engineering turbulence modelling for CFD with a focus on explicit algebraic Reynolds stress models. Stockholm, 254.
17. Aliev, E. B., Bandura, V. M., Pryshliak, V. M., Yaropud, V. M., Trukhanska, O. O. (2018). Modeling of mechanical and technological processes of the agricultural industry. INMATEH - Agricultural Engineering, 54 (1), 95-104.
18. Bhanage, G. B., Shahare, P. U., Aware, V. V., Dhandeand, K. G., Deshmukh, P. S. (2017). Development of stripper harvester for paddy. Journal of Applied and Natural Science, 9 (4), 1943-1948. doi: https://doi.org/10.31018/jans.v9i4.1469
19. Kozachenko, O. V. (2018). Pat. No. 135514 UA. Laboratorna ustanovka dlia doslidzhennia parametriv i rezhymiv protsesu obchisu-vannia silskohospodarskykh kultur. No. u201811954; declareted: 03.12.2018; published: 10.07.2019, Bul. No. 13.
