CC BY
9
Отримав розвиток метод компенсаци неактивних складових струмiв наванта-ження в трифазнй трьопровднт системi електропостачання шляхом симетруван-ня сигналiв напруги мережi живлення, що викликаш несиметрieю мережi живлення. Це дозволяв покращити енергетичт показ-ники системи електропостачання, зменши-ти значення реактивног потужностi, падш-ня напруги на опорах мережi, коефщент несиметрп i коефщент спотворення сину-согдностi струмiв i напруг мережi живлення Ключовi слова: активна компенсация, крос-векторна теоря, блок симетрування,
несиметрiя, частотна область
□-□
Получил развитие метод компенсации неактивных составляющих токов нагрузки в трехфазной трехпроводной системе электроснабжения путем симметрирования сигналов напряжения питающей сети, вызванных несимметрией питающей сети. Это позволяет улучшить энергетические показатели системы электроснабжения, уменьшить значение реактивной мощности, падения напряжения на сопротивлениях сети, коэффициент несимметрии и коэффициент искажения синусоидальности токов и напряжений питающей сети
Ключевые слова: активная компенсация, кросс-векторная теория, блок симметрирования, несимметрия, частотная область
UDC 621.311:621.314
|D0I: 10.15587/1729-4061.2017.87316|
IMPROVEMENT OF COMPENSATION METHOD FOR NON-ACTIVE CURRENT COMPONENTS AT MAINS SUPPLY VOLTAGE UNBALANC
Atef Saleh Al-Mashakbeh
PhD, Associate Professor Department of Electrical Engineering Tafila Technical University Et Tafila New Hauway str., 179, Tafila, Et Tafila, Jordan, 66110 E-mail: dr.atef_almashakbeh@yahoo.com M. Zagirnyak Doctor of Technical Science, Professor* E-mail: mzagirn@gmail.com M. Maliakova PhD, Senior Lecturer* E-mail: mariia.maliakova@gmail.com A. Ka l i n ov PhD, Associate Professor* E-mail: andrii.kalinov@gmail.com *Department of Electric Machines and Devices Kremenchuk Mykhailo Ostrohradskyi National University
Pershotravneva str., 20, Kremenchuk, Ukraine, 39600
1. Introduction
Nowadays the share of power-consuming loads of low-voltage power supply systems defined by nonlinearity of their characteristics and unbalance of parameters in phases has greatly increased. Such types of loads include welding apparatuses, controlled electric drives, electric-chemical plants, etc. Operation of such equipment results in occurrence of higher harmonics in currents and voltages and also in unbalance of voltages and currents in the power supply system. Consequently, non-active components appear in the load currents. According to the papers [1, 2], only the basic harmonic component being of a sinusoidal form and existing in the phase with the mains voltage is understood as active current. All the other load current components caused by the availability of nonlinear and asymmetric load are considered non-active [3].
The flow of current non-active components in power supply systems results in increase of losses in transformers, transmission lines, reactive power compensator capacitors, etc. and, consequently, in reduction of the efficiency of operation of low-voltage power supply systems [2-4]. Active power filters (APF) [4] are used to compensate for them in the frequency-domain as the most up-to-date, flexible and efficient devices [5, 6].
The present economic situation, in particular, the rise of the cost of electric power for industrial enterprises, causes the necessity and topicality of the problem of improvement of the efficiency of compensation for nonlinear and asymmetric power-consuming equipment negative influence on low-voltage supply mains.
2. Literature review and problem statement
It is known that calculations of compensation currents for APF in three- and four-wire power supply systems are done on the basis of the known theories of instantaneous power (IP) [7, 10]: p-q [4], cross-vector [5] and p-q-r ones [5, 6]. It is known from these theories that all three-phase power components consumed by the load, apart from IP constant component, are undesirable [9-11].
However, the author of the papers [10, 11] demonstrates that under the condition of supply voltage distortion the efficient compensation for variable components of active and reactive power is impossible. It is caused by the fact that even when the sinusoidal character of the load currents is provided, but there is voltage distortion, the spectra of power variable components will contain higher harmonics and asymmetric components [11]. The presence of these components
©
is analytically demonstrated in the papers [10, 11]. As in APF operating with the use of IP p-q theory only distortions caused by the load are compensated for [12, 13], compensation for variable power components under the conditions of distorted supply voltage will only deteriorate the shape of the load current signals [2, 11]. It can be explained by the fact that interpretation of power components according to the IP p-q theory as well as other theories, does not answer the question what nonsinusoidality or unbalance is caused by: the load or the mains [11, 14, 15]. The above said explains the urgent interest of contemporary scientists [9, 12, 14] in the problem of research in the frequency-domain and the time-domain of compensation processes in power supply systems to improve the method of compensation for current non-active components when the supply mains voltages are asymmetric [11, 14, 15].
in it. Moreover, there is no necessity for transition to a, ß, 0 coordinate system. This essentially simplifies the process of analytical research and determination of compensation currents.
During the research in an analytical form it was assumed that there was no currents influence on the mains voltage distortion, i. e. power supply system was believed to have unlimited power. Orthogonal cosine and sine frequency components were written down in the form:
1,
UA . = -U. ,
A al 2 1m
UAM = 0,
uBal=-4Ulm,
3. The purpose and tasks of the research
The purpose of the paper consists in improvement of the method of compensation for current non-active components, when the supply mains voltage is asymmetric, via research in the frequency-domain and the time-domain of compensation processes in power supply systems.
To achieve the stated purpose the following tasks were formulated:
- analysis in the frequency-domain and in the time-domain of the compensation processes for power non-active components with the use of IP cross-vector theory in the analytical form;
- revealing the ways to improve operation of the system of compensation for current non-active components in the presence of harmonic distortions and supply voltage unbalance with the use of research on mathematical models;
- improvement of the efficiency of operation of power supply system when asymmetric equipment is connected under the condition of power supply voltage unbalance.
4. Research of compensation processes in an analytical and numerical form in the frequency- and time-domains
4. 1. Research of compensation processes in an analytical form in the frequency-domain
The critical literature review demonstrates that analytical research in the frequency domain, i. e. analysis with the use of harmonic components [16, 17], provides better opportunities for the analysis of supply mains operating modes and nonlinear load. It allows one to properly research both simple nonlinear electric circuits [18-20], and more complicated electrotechnical complexes [21] and power supply systems [14, 15].
That is why an analytical calculation of processes in the frequency-domain with compensation for three-phase asymmetric load was performed in the paper. In this case the IP cross-vector theory was used as the problem posed in the paper consisted in research of the quality of operation of APF, built based on the IP p-q theory, in the frequency-domain and in the time-domain under the conditions of unbalance of supply mains voltage. This choice was caused by the fact that cross-vector theory is analogous to the IP p-q theory and all drawbacks described for the IP p-q theory are inherent
U =—U
UBb1 = 4 u1m,
UC 1 =— U1m,
Cal 4 Im'
V3,
Ucbi = -^Ulm.
Substitution of numerical values into the analytical expressions was used for visualization of the initial and obtained data and also for control of the analytical results correctness. In this case the following was assumed: maximum amplitude value of phase voltage U1m=311 V, shift angle of the first harmonic component of voltage ^U1=0 el. deg., shift angle of the first harmonic component of current ^I1=-30 el. deg.
Orthogonal cosine and sine frequency components of three-phase current:
V3T
Aal = 4 ïlm-
Ab1 = 4^1m'
,= 0,
i b1 = 2 eBI1m'
^ T
Ca1 = , £CT1m>
Cb1 = 4 £CI1m'
where £B, £C - unbalance coefficients of phase B and phase C, respectively. Numerical values of unbalance coefficients were assumed eB=0.8, eC=1.2. Three-phase asymmetrical current curves are shown in (Fig. 1).
In case of asymmetrical load, causing amplitude unbalance of the mains currents, there occur variable components of instantaneous active and reactive IP. When they are written in the frequency-domain in accordance with IP cross-vector theory, the following expressions are obtained:
constant component of instantaneous reactive power:
1
P0 = 2Uim!im cos (çn )[l+eB + ec ] ;
(1)
- cosine orthogonal component of the second harmonic of instantaneous reactive power:
1
P2a = gUüJlm COS Çn [2 - £ß - £c ] +
V3
+ g U1m^1m Sin (9n )[eB -EC ] i
(2)
- sine orthogonal component of the second harmonic of instantaneous reactive power:
1
P2b = 8 U1mI1m SÍn (9li )[2 -EB -EC ] +
^TUimIim cos (9ii )[ec-eb ] ;
(3)
- root-mean-square (RMS) value of the second harmonic of instantaneous active power:
P2rms = V P2a + P2b =
= [l + eB2 + ec2 -eceb -Ec -eb]; (4)
- constant component of reactive power:
V3
Qo = ^UlmIlm sin (çn )[!+eB + ec ] ;
(5)
- cosine orthogonal component of the second harmonic of instantaneous reactive power:
3
Q2a = 8U1m!im COS (çn )[ec - £ß ] +
V3
+ g U1mI1m Sin (9n )[2-EB -EC ] i
(6)
- sine orthogonal component of the second harmonic of instantaneous reactive power:
3
Q2b = -8Uim!im sin (çn )[eB -ec ]■
V3
g U1m^1m COs (9n )[2-£b -£c ] i
(7)
- RMS value of the second harmonic of instantaneous reactive power:
Q2rms = V Q2a + Q2b =
Vs
4
= "4su1ml1^[1 + £b2 + eg2 - egeb -eg -eb]•
(8)
The study of the obtained expressions in an analytical form revealed that the level of variable power components nonlinearly depends on the level of unbalance, and RMS values of the second harmonic of instantaneous active P2rms and reactive Q2rms powers do not depend on the shift angle of the
current phases in relation to voltage. Also, expressions (1)-(8) showed that unbalance of supply voltage caused appearance of variable components of instantaneous active power but does not cause appearance of variable components of reactive power. Moreover, asymmetrical load results in appearance of variable components of both active and reactive power.
Fig. 1. Three-phase amplitude-asymmetrical load current
According to the cross-vector theory compensation currents in the frequency-domain were calculated: - for phase A
^Aa1 = 123 [-2 + £B +£C ]; ^Abi = -^1I1m'
1 +E+E
- for phase B
^Bai = "24I1m +£B + £C ] ; ^Bbi =
- for phase C
V3 1
Icai [1 + £B -5EC ] i Icbl = ^ [l + £B -£C ] •
Correctness of the obtained orthogonal frequency components of compensation current was confirmed by the fact that when condition eB=eC=1 was substituted into them, expressions (1)-(8) take a form, describing the operation of the system with symmetrical load, i. e.: P2a=0; P2b=0;
Q2a=0; Q2b=0; P2rms=0; Q^O; Po = f^cos(9ll). The
high-quality process of compensation results in achievement of amplitude symmetry of currents, which is illustrated in Fig. 2.
Fig. 2. Compensated currents in mains with asymmetric load
The obtained analytical dependences will allow research for both small deviations of resistances in phases and for cases of limit conditions: open-phase fault (e=0) and short circuit (1/£=0).
Analysis of IP components depending on the change of coefficient e of current amplitude unbalance (Fig. 3, 4)
E
and coefficient 1/e of the change of load resistance in one of phases (Fig. 5, 6) will enable determination of integral parameters of power processes. They can also be used for calculation of parameters and adjustment of power of APF.
Fig. 3. Constant components of active P0 (-) and
reactive Qo (---) powers dependence on the coefficients
of current unbalance
Fig. 4. RMS values of components of active P2rms (-) and
reactive Q2rmS (---) powers dependence on
the coefficients of current unbalance
Iam = 0,
T =-—T £
B al 4 A1mfcB>
t
TBbi = 4 Tim£B'
I =— I £
C al 4 A1mcC>
t JT
TCbi 4 Tim£C*
Fig. 6. RMS values of components of active P2rms (-)
and reactive Q2rms (---) powers dependence on
the coefficients of change of load resistance 1/e in one of the phases
After compensation for undesirable IP components the following analytical expressions of compensation currents are obtained: - for phase A
i = ii
A al 2
1 + £n+£r
I
A b1
= 0;
- for phase B
i =-ii Bal 4 Alm
1 + £n+£r
V3T
- for phase C
Fig. 5. Constant components of active P0 (-) and
reactive Qo (---) powers dependence on the coefficients
of change of load resistance 1/e in one of the phases
To find out the mechanism of currents amplitudes distribution and to determine their dependence on the unbalance coefficient a study in an analytical form was performed in the frequency-domain of generation of compensation currents with elimination of unbalance of active load. Initial harmonic components of current are given below:
i = ii
A al 2
I =-1l
C al 4 Alm
1 + £n+£r
3
^Bbi 4 ^im
I = -^I
iCb1 = , 1
1 + £n+£r
1 + £n+£r
3
On the basis of the obtained expressions it is possible to
ri + £r + £,
come to the conclusion that expression
3
is
introduced into the composition of orthogonal components of current of every phase, which allows balancing of current signals amplitudes. That is, currents amplitudes are averaged.
This conclusion and obtained analytical dependences of compensation currents will make it possible to determine the charge of power switches of APF phases and make its correct choice according to the current of the most overcharged switch of the inverter.
It should be mentioned that the analysis of the obtained expressions for compensation for non-active components of current in the frequency-domain demonstrated that the APF correct operation is possible without taking into account asymmetrical components of supply voltage and harmonic distortions [14, 15], caused by load impact on current signals curves. It means that independently of the cause of current unbalance: load or supply mains, the use of harmonic components of voltage, without taking into account their asymmetric components, in generation of compensation currents will enable high-quality compensation. It provides certain possibilities for improvement of compensation methods.
4. 2. Research of compensation processes in the timedomain with the use of numerical mathematical modeling
The following stage of the research consisted in assessment of voltage unbalance influence on compensation processes with the use of numerical modeling methods. In this case a hypothesis was suggested that it is necessary to supply signals of the supply mains to APF control system (CS) into the algorithm of compensation currents generation without taking into account asymmetrical components caused by unbalance of supply voltage.
A mathematical model of a section of power supply was worked out for research of modes of compensation for non-active components of load currents in the presence of unbalance of supply mains voltages (Fig. 7). It consists of linear active-inductive load, active-inductive resistances of the mains, current and voltage measuring blocks, a compensator, a CS compensator, a voltage signal balancing block (VSBB), and also a separation block (SB) [14, 15]. For performance of preliminary research during mathematical modeling APF was represented as a controlled current source. That is, the influence of pulse-width modulation was not taken into consideration during the analysis of compensation processes.
The linear load parameters: for Psc/Pl=5 - Ll=1-10-3 Hn, RL=0.04 Ohm, for PSC/PL=20 - LL=3.8-10-3 Hn, RL=1.8 Ohm. A throttle with parameters Lr=0.3-10-3 Hn, Rr =0.01 Ohm was inserted in series into the compensator circuit. The level of unbalance of supply voltage was assessed by the coefficient of reverse sequence and was assumed equal to 3.98 % for the case when Psc/PL=5, and 4.03 % for - PSC/PL=20. VSBB was used for realization of the method proposed by the authors (Fig. 8).
Fig. 8. Voltage signal balancing block
It is designed for balancing signals of supply voltage before their transfer to compensator CS. Amplitude values of voltage in every phase are determined in VSBB with the help of block "Fourier transform" (Fig. 8, I). The obtained numerical values are added, then averaged (Fig. 8, II), coefficients KA, KB, KC are determined by division of the obtained values by the initial amplitude (Fig. 8, III); these coefficients are necessary for balancing the voltage amplitudes of every phase (Fig. 8, IV). Thus, thereafter, a voltage signal without components caused by supply voltage unbalance is transferred to compensator CS.
5. Results of the research of analyzing the proposed compensation system operation in the time-domain
5. 1. At asymmetric supply voltage and linear symmetric load
A case of operation of a section of power supply mains with supply voltage unbalance and linear load was considered. During the research unbalance was introduced into phase A by the value of coefficient eA=0.885 (Fig. 9). In this case the level of unbalance by coefficient K2U of reverse sequence of voltage was equal to 3.98 %. In such a system supply voltage unbalance (Fig. 9) causes amplitude unbalance of currents at the point of charge connection (Fig. 10). In this case a known compensator (Fig. 9, 10) operated rather efficiently - enabling achievement of current unbalance level according to coefficient K2U equal to 1.76 %, which is within the admissible norms [22, 23]. It is necessary to point out that APF with CS created with the use of IP cross-vector theory was used as a known compensator [6, 7].
However, as the author of the papers [9-11] pointed out, at section II (Fig. 9, 10), where operation of the known compensator is demonstrated, significant harmonic distortion of voltage and current signal form was observed [14, 15]. They were assessed by the coefficient of total harmonic section SC were assumed for modeling PSC=1.64-106 W. distortions of voltages THDU and currents THDI [23]. For
Fig. 7. The mathematical model of power supply mains with a system of compensation at unbalance
Relation of short circuit (SC) power PSC to load power PL equal to five and twenty was chosen during the analysis of APF operation under the conditions of voltage unbalance. This corresponds to cases of "weak" and "strong" mains, i. e. when supply voltages are distorted under the impact of load currents significantly and insignificantly, respectively.
During the modeling process two configurations of the researched section of the power supply mains were analyzed: a source with asymmetric supply voltage - linear symmetric load, a source with asymmetric supply voltage - linear asymmetric load.
The following values of the parameters of the mains
the considered case (Fig. 9, II) and (Fig. 10, II) they made THDU=9 % and THD,=11 %. It was caused by the fact that a signal of asymmetric supply voltage was supplied to CS by the compensator.
To eliminate harmonic distortions of current and voltage signals, it was proposed to use a separation block (SB) to separate supply voltage harmonics caused by mains distortion (Fig. 11) [14, 15].
Fig. 9. Mains voltages (I), after (II) connection of a known compensator and after connection of a compensator with VSBB and SB (III)
Fig. 10. Mains currents (I), after (II) connection of a known compensator and after connection of a compensator with VSBB and SB (III)
Fig. 11. SB for voltage signals of supply mains
It is intended for elimination from the algorithm of formation of compensation currents [14, 15] of those voltage higher harmonics at the point of compensator connection
that are caused not by flowing currents of the load but by power supply distortion. Under real conditions these voltage harmonics can be caused by powerful nonlinear consumers connected closer to the power supply.
In SB with the use of fast Fourier transform (CFFT) transition into the frequency-domain is performed (Fig. 11, I), which makes it possible to determine voltage harmonic composition at the point of compensator connection. Determination of voltage harmonics caused by harmonic distortion in the mains is performed in SB due to the analysis of the sign of the corresponding frequency component of active power [20]:
P = P + P + + P
r0 r01 T r02 T ••• T 0n '
(9)
where P01 = IanUan+IbnUbn (Fig. 11, HX n - harmonic number, Ian, Ibn - cosine and sine harmonic components of current of the n-th harmonic, respectively, Uan, Ubn - cosine and sine harmonic components of voltage of the n-th harmonic, respectively.
According to [14, 15, 21], if the sign of the corresponding component coincides with the sign (Fig. 11, III), it means that the corresponding voltage harmonic is caused by mains distortions. If the signs do not coincide, it means that the corresponding voltage harmonic is caused by flow of nonsinusoidal currents of nonlinear load. Harmonics caused by mains distortion are eliminated from the obtained harmonic composition of voltage (Fig. 11, IV). After that, using inverse Fourier transform (ICFFT), transition to the time-domain is performed (Fig. 8, V). After these operations voltage without harmonic components caused by distortion of supply mains voltage is supplied to CS by the compensator.
The following parameters (Table 1) were calculated for quantitative assessment of compensation modes: THDj and THDU, voltage drop AU at supply mains resistances, RMS values of variable components of active prms and reactive qrms powers, constant component Q of reactive power, coefficients of unbalance of current K2I and voltage K2U according to reverse sequence. Also, correspondingly, power AP of losses at active resistances of supply mains and efficiency h of the supply mains [24] without taking into account and taking into account (APk, hk) current displacement were calculated. Current displacement was taken into account by increase of active resitance Rk at the k-th harmonic by Vk times. The data are given for operation modes at PSC/PL=5 and PSC/PL=20.
The obtained data (Table 1) demonstrated that compensation with the use of VSBB and SB, in comparison with known compensation, made it possible to achieve better balancing of current signals with coefficient K2I=0.176 %. Also, it made possible to reach practically zero value of THDt and THDU, reduction of voltage drop at mains resistances AU; decrease of reactive power, variable components of active p rms and reactive qrms powers, decrease of losses and, consequently, increased efficiency. Such results are observed at operation modes with both significant (Psc/Pl=5), and insignificant (PSC/PL=20) distortion of currents and voltages signals.
Table 1
Indices of APF operation in mains with symmetrical supply voltage and symmetrical linear load
Parameter/ Mode AU, V THDd, % THDj, % q rms, VA Prms' VA Q, var AP, W APt, W n, % nt, % K2Ü, % K2I, %
Psc/PL=5
Before compensation 27.84 0 0 1.05-103 1.15104 1.22-105 1.96-104 1.965-104 92.5 92.45 3.98 3.98
After compensation 31.4 11 9 1.99104 1.14-104 100 1.386 104 1.386-104 94.7 94.69 4.1 1.76
After comp. with VSBB and SB 24.25 0.2 0.005 1031 3465 -85 1.383-104 1.383-104 94.72 97.72 4.25 0.176
Psc/Pl=20
Before compensation 7.38 0 0 400 1-104 3.19-104 1374 1377 92.85 91.9 3.99 3.985
After compensation 6.55 0.5 5.06 1000 235 40 997 998 94.7 94.69 4.022 1.499
After comp. with VSBB and SB 6.52 0.3 2.1 500 928 -9 994 994 94.73 94.73 4.068 0.092
5. 2. At asymmetric supply voltage and asymmetric linear load
A case of operation of power supply mains section with supply voltage unbalance and asymmetrical linear load was considered. During the research unbalance was introduced into phase A of supply voltage by the value of coefficient £a=0.885 and into phase C of the load by reduction of its active resistance by 10 % (Fig. 11, 12). In this case the unbal-
ance according to coefficient K2U of reverse sequence voltage made 4.03 %.
Under such operation conditions (Fig. 11, 12) variation of operation indices similar to those in the previous case can be observed. Compensator with VSBB and SB enabled reduction of load current unbalance to K2U=1.72 % and support of THDI and THDU at practically zero level (Table 2).
Table 2
Indices of APF operation in mains with symmetrical supply voltage and asymmetrical linear load
Parameter/ Mode AÜ, V THDÜ, % THDI, % q rms, VA P rms, VA Q, var AP, W APt, W n, % nt, % K2U, % K21, %
Psc/PL=5
Before compensation 27.25 0 0 3500 1.2104 1.18-105 1.89104 1.9104 92.8 92.05 4.03 4.87
After compensation 27.2 7.3 7.35 1.3-104 7700 450 1.36104 1.362-104 94.71 94.7 4.15 1.72
After comp. with VSBB and SB 24.15 0.002 0.005 5510 5294 -93.5 1.35104 1.35-104 94.72 94.72 4.32 0.17
Psc/Pl=20
Before compensation 7.2 0 0 1002 3600 -3.07-104 1316 1316.4 94.4 94.4 4.01 4.9
After compensation 6.43 0.5 5.05 929 236.4 30 968.4 968.8 94.71 94.705 4.023 1.46
After comp. with VSBB and SB 6.42 0.05 0.4 1584 1566 -7 966.3 996.3 94.72 94.72 4.067 0.09
Fig. 12. Mains voltages (I), after (II) connection of a known compensator and after connection of a compensator with VSBB and SB (III)
Fig. 13. Mains currents (I), after (II) connection of a known compensator and after connection of a compensator with VSBB and SB (III)
6. Discussion of the research results of analyzing the proposed compensation system operation in the time-domain
The subsystem of balancing the supply mains voltage signals, proposed in the paper, made it possible to improve the method of compensation for currents non-active components under the conditions of the supply mains voltages unbalance. The performed mathematical modeling of the researched system and analysis of the obtained numerical data revealed the efficiency and feasibility of the use of the proposed meth-
od of compensation for currents non-active components in power supply systems.
Improvement of the method consists in exclusion of voltage asymmetric components, caused by the mains distortions, from the algorithm of compensation currents generation. The latter enabled improvement of the efficiency of power supply systems operation and the speed of compensation system operation.
In the future, the proposed method can be applied to compensation for currents non-active components in the industrial power supply systems to which nonlinear and asymmetric equipment with sharply changing operation mode is connected.
7. Conclusions
1. The analysis in the frequency-domain of the processes of compensation for current non-active components in power supply systems with asymmetric load made it possible to obtain analytical expressions for compensation currents. It provided the possibility to determine the ways of improvement of currents non-active components compensation methods under the conditions of operation with supply mains asymmetric voltage. The obtained compensation currents analytical dependences will also enable determination of the charge of APF phases power keys and provide its correct choice according to the current of the most overloaded key of the inverter.
2. The research of the processes of compensation for load currents non-active components of a supply mains section at supply voltage unbalance was carried out in the time-domain on a mathematical model. On their basis, it was shown that the use of the developed method with balancing and separation of supply voltage signals harmonics, as compared with the known compensation system, makes it possible to:
- decrease the level of currents signals unbalance with reverse sequence coefficient by 1.3..1.5 %;
- achieve practically zero value of the currents nonsinu-soidality coefficient;
- reduce the value of reactive power after compensation by 15..23 % and voltage drop at the mains resistances by 0.5..23 %.
3. The use of the proposed method made it possible to improve the effectiveness of the power supply system, in particular, to reduce losses in transmission lines by 0.5 % and to increase the efficiency of the power supply system by 0.3..2.5 %.
References
1. Peng, F. Z. Definition and compensation of non-active current in power systems [Text] / F. Z. Peng, L. M. Tolbert, Z. Qian // 2002 IEEE 33rd Annual IEEE Power Electronics Specialists Conference. Proceedings (Cat. No.02CH37289). - 2002. doi: 10.1109/ psec.2002.1023068
2. Czarnecki, S. L. Instantaneous reactive power p-q theory and power properties of three-phase systems [Text] / L. S. Czarnecki // IEEE Transactions on Power Delivery. - 2006. - Vol. 21, Issue 1. - P. 362-367. doi: 10.1109/tpwrd.2005.852348
3. Czarnecki, S. L. Effect of supply voltage harmonics on IRP - based switching compensator control [Text] / L. S. Czarnecki // IEEE Transactions on Power Electronics. - 2009. - Vol. 24, Issue 2. - P. 483-488. doi: 10.1109/tpel.2008.2009175
4. Akagi, H. Instantaneous power theory and applications to power conditioning [Text] / H. Akagi, E. H. Watanabe, M. Aredes. - John Wiley & Sons, 2007. - 379 p. doi: 10.1002/0470118938
5. Kim, H. Instantaneous power compensation in three-phase systems by using p-q-r theory [Text] / H. Kim, F. Blaabjerg, B. Bak-Jensen, J. Choi // IEEE Transactions on Power Electronics. - 2002. - Vol. 17, Issue 5. - P. 701-710. doi: 10.1109/tpel.2002.802185
6. Kim, H. Spectral analysis of instantaneous powers in single-phase and three-phase systems with use of p-q-r theory [Text] / H. Kim, F. Blaabjerg, B. Bak-Jensen // IEEE Transactions on Power Electronics. - 2002. - Vol. 17, Issue 5. - P. 711-720. doi: 10.1109/ tpel.2002.802188
7. Domnin, I. F. Modern power theories and their usage in power electronics converter systems [Text] / I. F. Domnin, G. G. Gemerov, D. S. Krylov, E. I. Sokol // Tekhnichna elektrodynamika. - 2004. - P. 80-90.
8. Gemerov, G. G. Fryze power theory and modern power theories [Text] / G. G. Gemerov, I. A. Iljina // Electrical engineering & Electromechanics. - 2007. - Issue 6. - P. 63-65.
9. Czarnecki, S. L. On some misinterpretations of the instantaneous reactive power p-q theory [Text] / L. S. Czarnecki // IEEE Transactions on Power Electronics. - 2004. - Vol. 19, Issue 3. - P. 828-836. doi: 10.1109/tpel.2004.826500
10. Czarnecki, S. L. Comments to the paper: Instantaneous p-q theory for compensating nonsinusoidal systems [Text] / L. S. Czarnecki // Przegl^d Elektrotechniczny (Electrical Review). - 2009. - Vol. 85, Issue 6. - P. 167-169. - Available at: http://www.lsczar.info/ doc/111%20Comments%20to%20p-q%20Watanabe.pdf
11. Czarnecki, S. L. CPC-based comparison of compensation goals in systems with nonsinusoidal voltages and currents [Text] / L. S. Czarnecki, S. S. Pearce // International School on Nonsinusoidal Currents and Compensation. - 2010. - P. 27-36. doi: 10.1109/isncc.2010.5524472
12. Javadi, A. Unfunctionality of the instantaneous p-q theory for the control of series active filters [Text] / A. Javadi, K. Al-Haddad // 2011 IEEE Electrical Power and Energy Conference. - 2011. doi: 10.1109/epec.2011.6070231
13. Herrera, R. S. Instantaneous reactive power theory to n wire systems [Text] / R. S. Herrera, P. Salmeron, J. R. Vazquez, S. P. Litran // 2007 IEEE International Symposium on Industrial Electronics. - 2007. doi: 10.1109/isie.2007.4374993
14. Zagirnyak, M. Analysis of operation of power components compensation systems at harmonic distortions of mains supply voltage [Text] / M. Zagirnyak, M. Maliakova, A. Kalinov // 2015 Intl Aegean Conference on Electrical Machines & Power Electronics (ACEMP), 2015 Intl Conference on Optimization of Electrical & Electronic Equipment (OPTIM) & 2015 Intl Symposium on Advanced Electromechanical Motion Systems (ELECTROMOTION). - 2015. doi: 10.1109/optim.2015.7426958
15. Zagirnyak, M. Compensation of higher current harmonics at harmonic distortions of mains supply voltage [Text] / M. Zagirnyak, M. Maliakova, A. Kalinov // 2015 16th International Conference on Computational Problems of Electrical Engineering (CPEE). -2015. doi: 10.1109/cpee.2015.7333388
16. Zagirnyak, M. V. Estimation of energy conversion processes in an electromechanical complex with the use of instantaneous power method [Text] / M. V. Zagirnyak, D. I. Rodkin, T. V. Korenkova // 2014 16th International Power Electronics and Motion Control Conference and Exposition. - 2014. doi: 10.1109/epepemc.2014.6980719
17. Polischuk, S. Yu. Analytical construction of coordinate systems in theory of instantaneous power of three-phase circuits to control the active filtering devices [Text] / S. Yu. Polischuk, M. Yu. Artemenko, V. M. Mykhalskiy // Tekhnichna elektrodynamika. Peretvorennya parametriv elektruchnoyi energii. - 2013. - Issue 2. - P. 25-35.
18. Zagirnyak, M. Analysis of electric circuits with semiconductor converters with the use of a small parameter method in frequency domain [Text] / M. Zagirnyak, M. Maliakova, A. Kalinov; A. Demenko, I. Dolezel, K. Hameyer (Eds.) // COMPEL - The international journal for computation and mathematics in electrical and electronic engineering. - 2015. - Vol. 34, Issue 3. -P. 808-823. doi: 10.1108/compel-10-2014-0260
19. Zagirnyak, M. An algorithm for electric circuits calculation based on instantaneous power component balance [Text] / M. Zagirnyak, A. Kalinov, M. Maliakova // Przegl^d Elektrotechniczny (Electrical Review). - 2011. - Vol. 87, Issue 12b. - P. 212-215. - Avalaible at: http://pe.org.pl/articles/2011/12b/59.pdf
20. Zagirnyak, M. Analysis of instantaneous power components of electric circuit with a semiconductor element [Text] / M. Zagirnyak, A. Kalinov, M. Maliakova // Archives of Electrical Engineering. - 2013. - Vol. 62, Issue 3. doi: 10.2478/aee-2013-0038
21. Zagirnyak, M. V. Elimination of the influence of supply mains low-quality parameters on the results of induction motor diagnostics [Text] / M. V. Zagirnyak, D. G. Mamchur, A. P. Kalinov // The XIX International Conference on Electrical Machines - ICEM 2010. - 2010. doi: 10.1109/icelmach.2010.5608071
22. DSTU IEC 61000-2-2-2001. Elektromagnitna sumisnist'. Chastyna 2. Elektromagnitna obstanovka. Rozdil 2. Rivni sumisnosti dlja nyz'kochastotnyh konduktyvnyh zavad ta sygnaliv system peredavannja v nyz'kovol'tnyh elektropostachal'nyh systemah zagal'nogo pryznachennja [Text]. - Derzhspozhyvstandart, 2001. - # 648.
23. IEEE Trial-Use Standard Definitions for the Measurement of Electric Power Quantities Under Sinusoidal, Non-sinusoidal, Balanced, Or Unbalanced Conditions [Text]. - 2000. doi: 10.1109/ieeestd.2000.93398
24. Gemerov, G. G. Energy efficiency of the current phase correction and active and reactive power ripple compensation in three-phase power supply system [Text] / G. G. Gemerov, I. F. Domnin, I. A. Iljina, D. V. Tugay // Tekhnichna elektrodynamika. Power systems and electrotechnological complexes. - 2007. - Issue 1. - P. 52-57.
