CC BY
22
№ 4 (109)
UNIVERSUM:
ТЕХНИЧЕСКИЕ НАУКИ
апрель, 2023 г.
DOI - 10.32743/UniTech.2023.109.4.15320
SYNTHESIS OF DEPRESSOR ADDITIVES BASED ON POLYPROPYLENE POWDER AND EFFECT ON LOW-TEMPERATURE PROPERTIES OF DIESEL FUEL
Ikramjan Sapashov
Post-doctoral student, Bukhara Institute of Engineering and Technology, Republic of Uzbekistan, Bukhara
Sadriddin Fozilov
Doctor of Technical Sciences, Professor, Bukhara Engineering and Technology Institute, Republic of Uzbekistan, Bukhara
Batirbay Seydabullaev
Master's student, Karakalpak state university named after Berdakh, Republic of Uzbekistan, Nukus
Islambek Polatov
Student,
Karakalpak state university named after Berdakh, Republic of Uzbekistan, Nukus
СИНТЕЗ ДЕПРЕССОРНЫХ ПРИСАДОК НА ОСНОВЕ ПОЛИПРОПИЛЕНОВОГО ПОРОШКА И ИХ ВЛИЯНИЕ НА НИЗКОТЕМПЕРАТУРНЫЕ СВОЙСТВА ДИЗЕЛЬНОГО ТОПЛИВА
Сапашов Икрамжан Яумытбаевич
докторант,
Бухарский инженерно-технологический институт, Республика Узбекистан, г. Бухара
Фозилов Садриддин Файзуллаевич
д-р техн. наук, проф., Бухарский инженерно-технологический институт, Республика Узбекистан, г. Бухара
Сейдабуллаев Батырбай Бахытбай улы
магистрант
Каракалпакского государственного университета
имени Бердаха, Республика Узбекистан, г. Нукус
Полатов Исламбек Оразалы улы
студент
Каракалпакского государственного университета
имени Бердаха, Республика Узбекистан, г. Нукус
ABSTRACT
The article studies the influence of additives synthesized on the basis of polypropylene copolymers with methyl acrylate on the low-temperature properties of diesel fuel. The results of the study showed that both synthesized depressant additives had a strong inhibitory effect on diesel fuel, while the threshold filtration temperature of 0,4 % diesel fuel was reduced from -10 0С to -22 0С, and the pour point - from -10 0С up to -27 0С.
Библиографическое описание: SYNTHESIS OF DEPRESSOR ADDITIVES BASED ON POLYPROPYLENE POWDER AND EFFECT ON LOW-TEMPERATURE PROPERTIES OF DIESEL FUEL // Universum: технические науки : электрон. научн. журн. Sapashov I. [и др.]. 2023. 4(109). URL: https://7universum.com/ru/tech/archive/item/15320
№ 4 (109)
UNIVERSUM:
ТЕХНИЧЕСКИЕ НАУКИ
апрель, 2023 г.
АННОТАЦИЯ
В статье изучено влияния присадок синтезированных на основе сополимеров полипропилена с метил акрилатом на низкотемпературные свойства дизельного топлива. Результаты исследования показали, что синтезированные депрессорные присадки 0,4% концентрации дизельного топлива предельная температура фильтруемости была снижена с -10 0С до -22 0С, а температура застывания - с -10 0С до -27 0С.
Keywords: polypropylene, powder, copolymer, depressant, additive, isotactic, atactic.
Ключевые слова: полипропилен, порошок, сополимер, депрессор, присадка, изотактик, атактик.
Introduction. The composition of diesel fuel, unlike other types of fuel, can vary significantly depending on the raw materials and production technology. To obtain highly efficient fuels, first of all, it is necessary to select high-quality raw materials and improve the technology of their production. However, it is impossible to solve the problem in principle without the use of additives [1].
The main active components of the developed depressant additives are polymers, vinyl acetate copolymers [2, 3], polymethylacrylate, ethylene poly-a-olefin [4], methacrylate-comalein anhydride [5], vinyl acetate copolymers tetrapolymer consisting of methacrylates with maleic anhydride and methacrylmorpholine and their amine compounds [6], dialkyl fumarate-styrene-vinyl acetate is a terpolymer [7], n-alkylacrylate-vinyl acetate-styrene is a triple copolymer [8], dimethyl fumarate is a vinyl acetate copolymer [9], dimeric surfactants [10].
In addition, the block copolymers polyethylene-poly (ethylene propylene) (PE-PEP), ethylene-propyl-ene show high efficiency as initiators controlling the size of paraffin particles formed in diesel fuel due to the presence of external groups [11, 12].
Our country has a sufficient base of local raw materials (monomers) for the production of synthetic depressors by increasing the production of polymer substances and increasing the production processes of secondary products and waste in addition to the main products [13].
Objects and methods of research. The raw material we selected is a secondary product of the polymer production process at Uz-Kor Gas Chemical LLC. Polypropylene powder is obtained by polymerization of propylene using a Ziegler-Natta catalyst (TiCUiMgC^) nCH2=CH(CH3) ^
[-CH2-CH(CH3)-]n when tested on an EVLAS-2M analyzer, the humidity was 10,97 % at a temperature of 102 0C, at 105,5 0C for one minute, a complete humidity drying [14].
Subsequently, the dried polypropylene powder was separated from the high-molecular fractions by re-precipitation from ethyl alcohol in solutions of hexane, heptane and ether, and then purified from the catalyst residues. Isotactic and atactic polypropylene were dissolved in p-xylene at 130-140 0C, when the solution was cooled to 25 0C, the isotactic part was precipitated, and the atactic part was dissolved in p-xylene.
The separated atactic and precipitated isotactic part was dissolved in p-xylene and toluene in the range of 8090 0C, then a methyl acrylate monomer was added, heated to 75-90 0C and a copolymerization reaction was carried out. The solution was placed in a three-necked flask equipped with a stirrer and a return refrigerator, in a three-necked flask equipped with a stirrer and a thermometer, the amount of polypropylene and methyl acrylate was taken up to 1:9 in organic solvents - toluene, benzene or p-xylene. The resulting copolymer was precipitated with alcohol, the reaction mixture was filtered and weighed after cooling to room temperature.. The number of monomers in the resulting copolymer and the molecular weight of the copolymers, as well as their structure, were checked by IR spectroscopy.
Results and discussion. The structure of the obtained copolymer was analyzed by IR Shimadzu IRAffinity-1S spectroscopy device. Comparing the IR spectra of polypropylene and methyl acrylate copolymers with a polypropylene monomer, one can clearly see the absorption region characteristic of fragments in the IR spectrum of the copolymer.
"y^t——-Ч
UNIVERSUM:
ТЕХНИЧЕСКИЕ НАУКИ
апрель, 2023 г.
Figure 1. IRAffinity-1 S FOURIER TRANSFORM INFRARED SPECTRO-PHOTOMETER (SHIMADZU) IR spectrum of grafted polypropylene and methyl acrylate copolymer
It can be seen from the IR spectrum (Fig. 1) that the absorption region of 2866,22 cm-1 corresponds to ysim vibrations of the C-H bond in the CH3 group, the absorption region of 2918,30 cm-1 corresponds to yasim valence vibrations of this group, as well as 1375,25 cm-1 absorption area to ôasim deformation vibration of the C-H bond, 2918,30 cm-1 absorption area to the valence vibrations of the methylene group CH2 of the C-H bond, 2839, 22 cm-1 of the absorption area with the same valence of the methylene group C-H, the vibrations of the C-H bond, the absorption area 2357,01 cm-1 refers to the vibrations of the alkyl group C-O, The absorption area of 1734,01 cm-1 refers to the oscillation of the C= O-group bond, and 1166,93 cm-1 refers to the deformation vibrations of the C-C bond [15].
According to the results, the number of monomers in the ratio 1:1, 4:1, (0,2-0,4 mas. %) in copolymers of polypropylene and methyl acrylates tested in the conditions of the industrial laboratory of the Fergana Oil Refinery, due to the low-temperature properties of diesel fuel, 0,2 wt.% of copolymers of polypropylene and methyl acrylate in a ratio of 4:1 reduces the turbidity temperature of diesel fuel to -5 0C, the freezing temperature is -26 0C, the maximum filtration temperature is -16 0C, 0,4 wt. % of polypropylene and methyl acrylate copolymers in a ratio of 1:1 Compared with a ratio of 4:1, the lower turbidity temperature did not change at -5 0C, the freezing temperature -27 0C, the maximum filtration temperature -22 0C.
Table 1
Analysis results
CFL
Name of indicators Control method The norm for O'ZDST 989:2001 Diz. top. without additive Diesel. top. with additive 0,4%
1. Cetane index, at least GOST 3122 50 53,5 51
2. Density , kg/m3 , no more at 20 0C GOST 3900 863,4 860 861,4
3. Fractional composition: 50 % distilled at 0C, not higher than 95 % distilled at 0C, not higher GOST 2177 280 360 262 346 263 356
4. Water content GOST 2477 Absence absence absence
5. Maximum filterability temperature, 0C not higher, EN 116 - 15 - 10 -22
6. Iodine number, g per 100 g of fuel, no more GOST 2070 5 1,47 1,43
7. Coking capacity of 10% residue, % no more ASTM D 4530 0,20 0,19 0,015
8. Ash content, % (mass fraction), no more GOST 1461 Absence 0,01 absence
№ 4 (109)
UNIVERSUM:
ТЕХНИЧЕСКИЕ НАУКИ
апрель, 2023 г.
CFL
Name of indicators Control method The norm for O'ZDST 989:2001 Diz. top. without additive Diesel. top. with additive 0,4%
9. Mass fraction of sulfur, %, no more, in fuel type I type II type III GOST 19121 0,100 0,050 0,035 0,042 0,04
10. Mass fraction of mercaptan sulfur %, no more GOST 17523 0,01 0,01 0,0006
11. Hydrogen sulfide content ASTM D 3227 Absence absence absence
12. Copper plate test ASTM D 130 Withstands Class 1 Withstands Withstands
13. Content of water-soluble acids and alkalis GOST 6307 Absence absence absence
14. Kinematic viscosity at 20 0C, mm2/s, within GOST 31391 3,0-6,0 4,8 4,14
15. Acidity, mg, KOH per 100 cm3 of fuel, no more GOST 5985 5 0,25 0,1
16. The flash point determined in a closed crucible, 0C, is not lower than: -for diesel and marine diesel engines and gas turbines GOST 6356 62 55 87 53 85
17. Mechanical impurities, %, no more GOST 6370 0,0024 0,0014 0,0014
18. Concentration of actual resins, mg per 100 cm3 of fuel, no more GOST 8489 40 absence 10
19. Solidification temperature, 0C not higher, GOST 20287 - 25 - 10 - 27
20. Turbidity temperature, 0C not higher, GOST 5066 - 5 - 5 - 5
The effect of additives based on polypropylene powder and methyl acrylate on the physic-chemical and operational properties of fuel according to O'ZDTS 989:2001 when introducing a 0,4 % additive solution into hydro treated diesel fuel TD-L of the Fergana Oil Refinery, the general characteristics of the theoretical justification of the effect of additives on improving the low-temperature properties of winter diesel fuel are presented in table -1.
From the obtained results, it can be seen that the developed depressor has a positive effect on the solidification temperature of diesel fuel when it is used in the amount of 0.4 % in the fuel.
Conclusion. As a result of the conducted research, the following conclusion can be made: polypropylene powder from secondary products of the Uz-Kor Gas Chemical LLC polymer workshop can be used as depressant additives to diesel fuel, and when added to summer diesel fuel from a 0.4% additive solution, it improved its low-temperature properties, did not affect the basic physico-chemical properties and was recognized as fully compliant with the technical requirements of O'ZDTS 989:2001.
References:
1. Импорт урнини босувчи ^ундирмаларни мах,аллий хом ашёлардан олиш ва уларни дизель ё^илгилари хоссаларини яхшилашда ^уллаш. ^ора^лапогистон Республикасида ишлаб чи^ариш саноати сох,алари ривожининг долзарб муаммолари. Республика илмий-амалий анжуман материаллари туплами. Нукус-2021. 163 б.
2. Farazmand S., Ehsani M.R., Shadman M.M., Ahmadi S., Veisi S., Abdi E. (2016) The effects of additives on the reduction of the pour point of diesel fuel and fuel oil, Pet. Sci. Technol. 34, 17-18, 1542-1549.
3. Zhou M., He Y., Chen Y., Yang Y., Lin H., Han S. (2015) Synthesis and evaluation of terpolymers consist of meth-acrylates with maleic anhydride and methacrylic morpholine and their amine compound as pour point depressants in diesel fuels, Energy Fuels 29, 9, 5618-5624.
4. Zhao Z., Xue Y., Xu G., Zhou J., Lian X., Liu P., Chen D., Han S., Lin H. (2017) Effect of the nano-hybrid pour point depressants on the cold flow properties of diesel fuel, Fuel 193, 65-71.
5. Xu G., Xue Y., Zhao Z., Lian X., Lin H., Han S. (2018) Influence of poly (methacrylate-co-maleic anhydride) pour point depressant with various pendants on low-temperature flowability of diesel fuel, Fuel 216, 898-907.
№ 4 (109)
UNIVERSUM:
ТЕХНИЧЕСКИЕ НАУКИ
апрель, 2023 г.
6. Zhou M., He Y., Chen Y., Yang Y., Lin H., Han S. (2015) Synthesis and evaluation of terpolymers consist ofmethacrylates with maleic anhydride and methacrylic morpholine and their amine compound as pour point depressants in diesel fuels, Energy Fuels 29, 9, 5618-5624.
7. Du T., Wang S., Liu H., Zhang Y., Song C. (2011) Study on dialkylfumarate terpolymer lowering cold filter plugging point for diesel fuel, Pet. Sci. Technol. 29, 17, 1753-1764.
8. Feng L.J., Zhang Z.Q., Wang F., Wang T., Yang S. (2013) Performance of AVS diesel fuel pour point depressant, Oilfield Chem. 30, 4, 586-589.
9. Du T., Wang S., Liu H., Zhang Y. (2010) Study on dibehenyl fumarate-vinyl acetate copolymer for lowering cold filter plugging point of diesel fuel, China Pet. Process. Petrochem. Technol. 12, 4, 52-56.
10. Maithufi M.N., Joubert D.J., Klumperman B. (2011) Application of gemini surfactants as diesel fuel wax dispersants, Energy Fuels 25, 1, 162-171.
11. W. Leube, M. Monkenbusch, D. Schneiders [et al.] Wax-crystal modification for fuel oils by self-aggregating partially crystallizable hydrocarbon block copolymers . Energy Fuels. - 2000. - Vol. 14. - No. 2. - P. 419-430.
12. M. Monkenbusch, D. Schneiders, D. Richter [et al.]. Aggregation behaviour of PE-PEP copolymers and the winter-ization of diesel fuel. Physica B: Condensed Matter. - 2000. - Vol. 276-278. - P. 941-943.
13. Сапашов И.Я., Фозилов С.Ф., Полатов И.О. UZ-KOR GAS CHEMICAL" ^К-МЧЖ иккиламчи махсулотларини фойдаланиш. Озиц-овцат махсулотлари ишлаб чицаришда илм-фан ва инноваион технологиялар. Халцаро илмий-амалий конференцияси. Бухоро 2022.
14. Sapashov I. Fozilov S. Mavlanov B. Polatov I. Depressor properties of the products of polymeranalogical changes of low molecular polypropylene // Universum: технические науки: электрон. научн. журн. 2023. 2(107). URL:https ://7universum.com/ru/tech/archive/item/15034
15. Сапашов Икрамжан, & Фозилов Садриддин. (2022). Пропилен гомо-ва сополимерлари асосида иккиламчи хомашёларнинг термооксидланишини урганиш. https://doi.org/10.5281/zenodo.7293053
