CC BY
9Бюллетень науки и практики /Bulletin of Science and Practice Т. 7. №5. 2021
https://www.bulletennauki.com https://doi.org/10.33619/2414-2948/66
UDC 581.5; 631.4 https://doi.org/10.33619/2414-2948/66/28
STUDY ON HEAT TRANSFER PERFORMANCE OF NON-INTEGRAL CAPILLARY CORE SINTERED UNIFORM PLATE
©Jiang Weiyu, ORCID: 0000-0003-0604-6184, Ogarev Mordovia State University, Saransk, Russia, Jiangsu University of Science and Technology, Zhenjiang, China, 1324947307@qq.com ©Sun Lili, ORCID: 0000-0002-9392-8937, Ogarev Mordovia State University, Saransk, Russia,
Jiangsu University of Science and Technology, Zhenjiang, China, 1640880760@qq.com ©Mao Jijin, ORCID: 0000-0002-5216-4168, Ogarev Mordovia State University, Saransk, Russia,
Jiangsu University of Science and Technology, Zhenjiang, China, 554436558@qq.com ©Zhang Donghui, ORCID: 0000-0002-9503-5809, Ogarev Mordovia State University, Saransk, Russia, Jiangsu University of Science and Technology, Zhenjiang, China, 2554304973@qq.com ©Levtsev A., SPIN-code: 7896-7312, Dr. habil., Ogarev Mordovia State University, Saransk,
Russia, levtzevap@mail.ru
ИССЛЕДОВАНИЕ ТЕПЛОВЫХ СВОЙСТВ ИЗОТЕРМИЧЕСКИХ ПЛИТ ПРИ СПЕКАНИИ КАПИЛЛЯРНОГО СЕРДЕЧНИКА
©Цзян Вэйюй, ORCID: 0000-0003-0604-6184, Национальный исследовательский Мордовский государственный университет им. Н. П. Огарева, г. Саранск, Россия, Цзянсуский университет науки и техники, г. Чжэньцзян, Китай, 1324947307@qq.com ©Сунь Лили, ORCID: 0000-0002-9392-8937, Национальный исследовательский Мордовский государственный университет им. Н. П. Огарева, г. Саранск, Россия, Цзянсуский
университет науки и техники, г. Чжэньцзян, Китай, 1640880760@qq.com ©Мао Цзицзинь, ORCID: 0000-0002-5216-4168, Национальный исследовательский Мордовский государственный университет им. Н. П. Огарева, г. Саранск, Россия, Цзянсуский университет науки и техники, г. Чжэньцзян, Китай, 554436558@qq.com ©Чжан Дунхуэй, ORCID: 0000-0002-9503-5809, Национальный исследовательский Мордовский государственный университет им. Н. П. Огарева, г. Саранск, Россия, Цзянсуский университет науки и техники, г. Чжэньцзян, Китай, 2554304973@qq.com ©Левцев А. П., SPIN-код: 7896-7312, д-р техн. наук, Национальный исследовательский Мордовский государственный университет им. Н. П. Огарева, г. Саранск, Россия, levtzevap@mail.ru
Abstract. This paper mainly introduces the sintering process of the monolithic capillary wick and analyzes the influence of different copper powder particle size, filling rate, copper powder shape and heat source size on the heat transfer performance of the isothermal plate. The experimental results show that: (1) For the isothermal plate sintered with spherical copper powder, the capillary force of large particle size copper powder is small, but the flow resistance is also small, and the performance of the isothermal plate sintered with large particle size copper powder is better. (2) In the case of low filling rate, the isothermal plate is dried due to insufficient return fluid. In the case of high filling rate, on the one hand, the thickness of the liquid film at the evaporation end of the isothermal plate is large, resulting in additional thermal resistance. On the other hand, the thin film evaporation mode will be transformed into pool boiling mode, which will reduce the heat transfer performance. (3) Spherical copper powder sintered plate with regular shape has the best performance, while dendritic copper powder sintered plate has relatively high thermal resistance. (4) The heat source area has a great influence on the thermal resistance of the plate. Under the same heating power, the thermal resistance of the small area heat source is much higher than that of the
Бюллетень науки и практики /Bulletin of Science and Practice Т. 7. №5. 2021
https://www.bulletennauki.com https://doi.org/10.33619/2414-2948/66
large area heat source; The thermal resistance of sintered copper plate is lower than that of pure copper plate under two heat source areas.
Аннотация. В данной статье описывается процесс агломерации неровных капиллярных сердечников, изучается влияние различных размеров медного порошка, наполнения жидкости, формы медного порошка, а также размер источника тепла на теплопередающие свойства изотермической пластины. Анализ результатов эксперимента показал: 1) для термостатных пластин спекания шаровой медной пыли, крупные частицы медного порошка, капиллярность мелкозернистой, но, соответственно, сопротивление текучести является небольшим, при этом большое количество медного порошка спекания имеет хорошую характеристику термостата; 2) толщина слоя дает дополнительное тепловое сопротивление, с другой стороны, тонкие мембраны испарения будут преобразованы в модель кипения бассейна, что снижает теплопередающие свойства; 3) форма более правильная шарообразная медная мука спекания средних температур пластины лучше, ветки медного порошка спекания относительно высокая тепловая блокировка; 4) площадь источника тепла оказывает большое влияние на термосопротивление изотермической пластины, то же самое нагревание при мощности тепловое сопротивление малой площади источника тепла значительно выше теплового сопротивления крупного источника, а по площади двух источников тепла спеченная медная плита из медного порошка ниже теплового сопротивления, чем чисто медная плита.
Keywords: uniform plate, non-holonomic capillary core, copper powder sintering and heat transfer performance.
Ключевые слова: изотермическая плита, неголономная капиллярная сердцевина, медная мука спекания, теплопередающая способность.
Introduction
Since the 21st century, with the continuous development of modern electronic technology, electronic components show the trend of miniaturization and high performance. Because electronic components have the characteristics of high calorific value, it will increase the temperature and reduce its performance. Generally, the heat power of the chip in each area of the electronic equipment is different, so the thermal stress on the surface of the chip is different, which is easy to reduce or even damage the performance of the electronic equipment, and the local high temperature hot spots are easy to burn the electronic device. Compared with the traditional heat pipe, from the analysis of the heat transfer path, the heat transfer of the heat pipe is in the one-dimensional direction. The uniform temperature plate realizes the heat transfer in the two-dimensional plane, which can effectively solve the 'hot spot' problem of electronic devices.
Tang Yong et al. [1] prepared a new type of sintered copper mesh core by weaving, chemical deposition and sintering. Alkali-assisted surface oxidation process [2] was used to treat the wick structure. The experimental results show that the sintering process is conducive to enhancing the adhesion strength of the surface structure. The capillary force of the deposited capillary core structure is greater than that of the normal capillary core. Through the deposition time of about 15 min and the sintering temperature of about 500 °C, the deposited liquid wick can achieve the best heat transfer performance. Lewis et al. [3] used polyimide film as coating material and lithography technology to manufacture the wick structure. The thickness of the wick was only 0.3 mm, and TiO2 was deposited on the surface of the wick by ALD process, which played a hydrophilic role. Under the condition that 0.15 ml water was filled in the ultra-thin hot pipe, the
heater area was 20 mm*10 mm, and the minimum thermal resistance measured in the experiment was 11.92 °C/W, and the effective thermal conductivity was as high as 541 W/(mK).
Li et al. [4-5] prepared a new type of wick structure, which is sintered from 50p,m to 100p,m mixed copper powder with thickness less than 1mm, and the total thickness of the copper-water flat heat pipe is 2mm. The effects of different heating power, inclination angle and cooling water temperature on the heat transfer performance of flat heat pipe were experimentally studied. The experimental results show that the maximum input power of the flat heat pipe in the horizontal direction is 120 W, and the minimum thermal resistance is only 0.196 °C/W. Weibel et al. [6] made an ultra-thin nanostructured temperature plate. The liquid wick adopts a 200 p,m thick copper powder sintering structure, and the carbon nanotubes (CNTs) shape is made into a mosaic array structure to enhance the ability of filling liquid in the cavity to infiltrate the liquid wick. The thickness of the isothermal plate is only lmm.
Test System for Heat Transfer Performance of Nonholonomic Capillary Core Isothermal Plate
The heat transfer performance test system mainly includes four parts: heating system, water cooling system, temperature plate, data acquisition system. In the isothermal plate performance test device, the clamping device is composed of two aluminum plates with a thickness of 30 mm, and the corners are fixed and tightened by M16 bolts, so that the middle part can be closely contacted. Wood insulation materials are arranged at the bottom of the plate and the top of the cooling water jacket to reduce heat loss. The temperature is set in the low-temperature tank. After the water is cooled, the circulating pump is opened to produce the cooling water. The flow rate is determined by adjusting the rotor flowmeter, and then enters into the cooling water jacket cavity, and the heat on the surface of the homogenizer is taken away. The temperature measuring device adopts armored thermocouple, connected with intelligent temperature inspector, and finally reads data on the computer, so as to complete the whole temperature measurement process.
Бюллетень науки и практики /Bulletin of Science and Practice Т. 7. №5. 2021
https://www.bulletennauki.com https://doi.org/10.33619/2414-2948/66
3 4
5 6
1
Figure 1. Experimental system schematic 1. Low temperature water tank 2. Experimental test section 3. Armored thermocouple 4. Temperature inspection instrument 5. Voltage regulator 6. Power supply 7. Rotor flowmeter 8. Computer
Figure 2. Vapor chamber testing system 1. Aluminum plate fixtures 2. Hard insulation materials 3. Cooling water jacket 4. Uniform plate 5. Heated copper block 6. Fastener bolts
Sintering process of non-integrated capillary core isothermal plate The main process of sintering process is as follows: the sintered copper powder liquid suction core is closely bonded to the off-duty, and the foamed copper is closely bonded to the upper plate. They are respectively tightened with fixtures and placed horizontally in the vacuum sintering furnace. Then the furnace door is closed for the next washing, and the vacuum is pumped to 0.05 Pa. After that, nitrogen is passed, vacuum is pumped again, and nitrogen is passed again, and hydrogen is passed. After setting the program, the switch is opened to start sintering. The sintering temperature is 950 °C, and the holding time is set to last for 3 hours. After sintering, the furnace door can be opened and the sample can be taken out under the condition of vacuum cooling in the sintering furnace, as shown in Figure 3.
The sintered wick was placed in the shell plate, and then the solder was placed between the
Бюллетень науки и практики /Bulletin of Science and Practice https://www.bulletennauki.com
Т. 7. №5. 2021 https://doi.org/10.33619/2414-2948/66
upper and lower shell plates. The whole device was fixed with a fixture and placed horizontally in a vacuum sintering furnace. The sintering process was the same as before, but the maximum temperature set during sintering was 780 °C. When the temperature rose to 780 °C, it immediately entered the natural cooling stage.
( a ) Evaporation end Figure 3. Capillary core combined with outer shell
( b ) condensation end
Taking the sintered copper powder structure as the lower wick and the foam copper structure as the upper wick, the influence of different wick structure and filling rate on the heat transfer performance of the isothermal plate was studied. The effects of different copper powder shapes on the heat transfer performance of the isothermal plate were studied. The heat transfer performance of the plate under different heating power was studied.
Experimental study on heat transfer performance of non-holonomic wicked plate
Experimental research content
The experimental research in this section is mainly divided into four parts:
Particle size parameter experiment of sintered copper powder
A total of 14 thermostats were prepared in this study. The particle sizes of spherical copper powder were 30 p,m, 50 p,m, 30 p,m, 30 p.m+90 p,m, and the particle sizes of dendritic copper powder were 30 p,m and 50 p,m, respectively. The experimental data of the thermostats with the best performance were recorded after the test of each thermostat.
Filling rate parameter experiments
In this experiment, there are four isothermal plates sintered with spherical copper powder. The porosity of 30p,m, 50p,m, 90p,m and 30p,m + 90p,m isothermal plates are 48.5%, 52.6%, 40.6% and 54.2%, respectively. The dendritic copper powder sintered temperature plate has two pieces, the porosity of 30p,m and 50 p,m is 74% and 71.1% respectively. The charging amount of uneven copper powder sintering temperature plate is shown in Table 1, and the charging amount of dendritic copper powder sintering temperature plate is shown in Table 2.
Table 1.
FILLING RATIO OF SPHERICAL COPPER POWDER SINTERED VAPOR CHAMBERS
70% 90% 120%
30цш (g) 2.91 3.75 5.00
50цш (g) 2.92 3.76 5.00
90цт (g) 2.47 3.18 4.24
30цт+90цт (g) 3.25 4.18 5.58
Experiment of copper powder shape parameters
The research object of this experiment is the sintered copper powder type isothermal plate. In this experiment, four isothermal plates were produced. The shape of copper powder of the sintered
Бюллетень науки и практики /Bulletin of Science and Practice Т. 7. №5. 2021
https://www.bulletennauki.com https://doi.org/10.33619/2414-2948/66
isothermal plate was spherical and dendritic, and the particle sizes were 30 p,m and 50 p,m, respectively. The heat transfer performance of the four isothermal plates was compared and analyzed under the conditions of three filling rates of 70 %, 90 % and 120 %.
Table 2.
FILLING RATIO OF DENDRITIC COPPER POWDER SINTERED VAPOR CHAMBERS
70% 90% 120% ~
30^m (g) 3.17 4.07 5.43
50^m (g) 2.71 3.48 4.64
Experiment of heat source size parameters
In this experiment, the copper plate sintered by spherical copper powder was selected, and the particle sizes were 30 p,m and 50 p,m, respectively. Two different sizes of heated copper blocks were designed: 15 mm*15 mm and 30 mm*30 mm, respectively. The heat transfer performance of the isothermal plate under different heat flux was compared and compared with the pure copper plate.
Experimental results and analysis Effect of Sintered Copper Powder Particle Size on Experimental Performance of Uniform Temperature Plate
The thermal resistance of the plate made of four spherical copper powders varies with heating power as shown in Figure 4 (a-c). The heat source area is 30 mm*30 mm and the filling rates are 70%, 90% and 120%, respectively. The experimental results show that with the increase of heat flux, the thermal resistance values of the isothermal plates with different particle sizes under different filling rates change linearly. From the trend of curve, the performance of the larger particle size plate is relatively good. From the experimental results, it can be seen that the performance of the homogenized plate sintered with large particle size spherical copper powder is better, which indicates that the liquid return resistance has a greater influence on the thermal resistance performance of the homogenized plate made of spherical copper powder and plays a leading role.
0.9
0.8
0.7
0.6
0.5
о 0.4
« 0.3
0.2
0.1
0.0
' —■— 30pm®
. 50pm®
- 90pm®
' 30pm+90pm®
A__▲
- ^ ^^ " __^
20 40 60 80 100 120 140 160 180
(a) 70% filling rate
0.9
0.8
0.7
0.6
¡Г 0.5
P 0.4
« 0.3
0.2
0.1
0.0
- 30pm® 50pm® 90pm® 30pm+90pm®
0 20 40 60 80 100 120 140 160 180
(b) Filling rate 90%
0
Бюллетень науки и практики / Bulletin of Science and Practice https://www.bulletennauki.com
Т. 7. №5. 2021 https://doi.org/10.33619/2414-2948/66
0.9 0.8 0.7
0.6
§ 05
Р 0.4
-
30pm+90pm®
0 20 40 60 80 100 120 140 160 180
(c) Filling rate : 120%
Figure 4. Thermal resistance of spherical copper powder sintered vapor chamber with heating power under different charging rates
Effect offilling rate on heat transfer performance of isothermal plate
Sintered copper powder is spherical. Figure 5 shows the thermal resistance changes of 30pm, 50pm, 90pm and 30pm + 90pm isothermal plates, respectively. Three different filling rates are compared. It can be seen from the figure that with the increase of heat flux, the thermal resistance values of isothermal plates with different particle sizes change linearly under different filling rates.
For the 30 pm isothermal plate, the thermal resistance is slightly smaller when the filling rate is 120% and the heating power is low. With the increase of heating power, the thermal resistance almost remains unchanged, and the filling rate has little effect on the thermal resistance. For 50 pm and 90 pm isothermal plates, the thermal resistance value of the isothermal plate is relatively low under the condition of low filling rate. Because the particle size of copper powder increases, the capillary force decreases, the flow resistance is small, and the filling rate is too high. The liquid will be immersed in the suction core, and the liquid film will be thickened, which will bring additional thermal resistance. Moreover, the viscosity of the liquid is much higher than that of the gas, so the steam movement will be resisted, resulting in the phenomenon of carrying, and the reflux is blocked. The 30 pm+90 pm plate is made of mixed particle size, which can balance the capillary force and flow resistance. When the filling rate is 90%, the lowest thermal resistance of the plate is 0.13 °C/W.
It is found that when the heating power is 50W, the thermal resistance of 30 pm, 50 pm and90pm plates is relatively flat. It may be because only when the heating power reaches a certain condition, the working fluid inside the wick of the evaporation end will completely absorb heat and vaporize, and the thermal resistance is also slowly reduced in the process of normal heat transfer. However, when the heating power is about90 W, this phenomenon occurs in the 30 pm + 90 pm plate. Because the 30 pm+90 pm plate has a relatively large amount of filling under the condition of the same filling rate, it needs to improve the heating power to provide the heat needed for the normal operation of the plate, so it will appear gentle phenomenon under the condition of large power.
0 20 40
60 80 Hill 120 140 160 180 #*(W)
60 80 100 120 140 160 180 #*(W)
0
20 40
Бюллетень науки и практики / Bulletin of Science and Practice https://www.bulletennauki.com
Т. 7. №5. 2021 https://doi.org/10.33619/2414-2948/66
(a) 30 цт plate
(b) 50 цш plate
0 20 40 60 80 100 120 140 160 180
0 20 40 60 80 100 120 140 160 180
(c) 90 цт plate
li^(W)
(d) 30цш + 90цш plate
Figure 5. Thermal resistance of spherical copper powder sintered vapor chamber at different charging
Effect of copper powder shape on heat transfer performance of isothermal plate Figure 6 (a-c) shows the effect of copper powder shape on the performance of the isothermal plate under different filling rates. It can be seen from the figure (a) that the thermal resistance of the spherical 50 pm plate is smaller, the thermal resistance of the spherical and dendritic 30 pm plate is similar, and the thermal resistance of the dendritic 50 pm plate is poor. Figure (b) shows that the thermal resistance of the spherical 50 pm plate is the smallest, the performance of the dendritic 50 pm plate is the worst, and the others are similar. Figure (c) shows that the thermal resistance of spherical and dendritic 30 pm plate is relatively small. On the whole, the thermal resistance of the thermostat made of spherical copper powder is smaller than that of the thermostat made of dendritic copper powder at three filling rates, which may be due to the fact that the wick made of dendritic copper powder has more blind pores ( that is, the pores are not interconnected), thus the number of flow channels of the liquid working medium is reduced, the flow is blocked and the heat transfer performance of the thermostat is affected.
0.9 0.8 0.7 0.6 о 0.5 p 0.4 Й 0.3 0.2 0.1 0.0
- 30pmS 9Ш 50pmS 1Ш 30pmS Mtttt 50pmS Mtttt
0 20 40 60 80 100 120 140 160 180
- 30pmS 1Ш 50pmS ЖШ 30pmS Mtttt 50pmS Mtttt
(a)
a*(W)
Thermal resistance comparison of 70% plate
20 40 60 80 100 120 140 160 180
a*(w>
(b) Thermal resistance comparison of 90% isothermal plate
0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0
- 30|rnffi ЪШ 50|rnffi Ш№
0 20 40 60 80 100 120 140 160 180
(c) Thermal resistance comparison of 120% isothermal plate Figure 6. Comparison of the thermal resistance of vapor chamber under different charging rates
0
Бюллетень науки и практики /Bulletin of Science and Practice Т. 7. №5. 2021
https://www.bulletennauki.com https://doi.org/10.33619/2414-2948/66
Effect of heat source size on heat transfer performance of isothermal plate
Figure 7 is the comparison of heat transfer performance between the uniform temperature plate and the pure copper plate made of copper powder with spherical shape, particle size of 30 pm and 50 pm under the conditions of two heat source sizes of 30*30 mm and 15 mm x 15 mm and filling rate of 70%.
It can be seen from the above figures that the failure power of the plate can reach 170 W under the condition of large heat source area, and the measured thermal resistance is smaller than that under the condition of small heat source area, because under the condition of the same heating power, the heat flux of the plate measured by large heat source area is relatively small, so the working fluid in the evaporation area is not easy to dry, and the liquid film is thin, so the thermal resistance value is low; The temperature uniformity of the plate is better than that of the pure copper plate, and the maximum temperature difference at the condensation end is small. The main reason is that the plate is sintered by copper powder, and the copper powder column (25 diameter is 3 mm) sintered by the wick at the evaporation end is connected with the rectangular convex ring of copper powder with a width of 2 mm around, so that there are more capillary channels and less reflux resistance, which greatly enhances the heat transfer ability, so the heat resistance value is small, which indicates that the process of the plate is effective.
18 16 14 12 £ 10
18 6
- 30x30 30pmfö 30x30 50pmfö 30x30 штш 15x15 30pmfö 15x15 50pmfö
- 15x15 шт
0 20 40
60 80 100 120 140 160 180
(a)
160 140 120 100 80 60 40 20 0
Maximum temperature difference comparison at condenser end
- 30x30 30pmfö 30x30 50pmfö
30x30 штш
15x15 30pmfö 15x15 50pmfö
- 15x15 штш
0 20 40
60 80 100 120 140 160 180
(c) Comparison of surface temperature of heat source
0.5
0.4
0.3
g
P 0.2
P"
0.1
0.0
-0.1
30x30 30x30
30x30 штш
15x15 30ртШ 15x15
15x15 шт ш
0 20 40
60 80 100 120 140 160 180
(b) Comparison of isothermal thermal resistance at condensation end
1.8
1.6
1.4
1.2
,—,
£ 1.0
P 0.8
Й
0.6
0.4
0.2
0.0
30x30 30pmfö 30x30 50pmfö
30x30 штш
15x15 30pmfö 15x15 50ртШ
15x15 штш
0 20 40 60 80 100 120 140 160 180
(d) Comparison of thermal resistance of isothermal plate
Figure 7. Heat transfer performance of vapor chamber under different heat sources
Summary
This chapter has carried on the experimental analysis to the heat transfer performance of the plate, from the copper powder particle size, filling rate, copper powder shape and heat source size four aspects to do the comparative analysis, the following conclusions:
Бюллетень науки и практики /Bulletin of Science and Practice Т. 7. №5. 2021
https://www.bulletennauki.com https://doi.org/10.33619/2414-2948/66
(1) In this paper, the upper and lower wicks are sintered with the shell plate respectively, and then the shell plate is welded. It can ensure the complete contact between the wick and the shell plate and reduce the contact thermal resistance. At the same time, the upper and lower wicks are also closely contacted, which reduces the reflux path. In the test process, when the maximum heating power reaches 170 W, the uniform temperature plate will not fail, so it can be considered as the preferred method of uniform temperature plate production.
(2) For the uniform plate sintered with spherical copper powder, the uniform plate sintered with large particle size of copper powder has good performance, and the capillary force of large particle size of copper powder is small, but the flow resistance is also relatively small, indicating that the liquid return resistance has a greater impact on the thermal resistance performance of the uniform plate made of spherical copper powder, which plays a leading role. For the uniform temperature plate sintered with dendritic copper powder, the performance of the uniform temperature plate sintered with small particle size copper powder is better, and the capillary force of the small particle size copper powder is larger, but the flow resistance is also large, indicating that the capillary suction has a greater influence on the thermal resistance of the uniform temperature plate made of dendritic copper powder and plays a leading role.
(3) When the filling rate is appropriate, the heat transfer performance of the isothermal plate is relatively excellent. When the filling rate is low, the isothermal plate will be dried due to insufficient return fluid. When the filling rate is high, on the one hand, the thickness of the liquid film at the evaporation end of the isothermal plate is large, resulting in additional thermal resistance. On the other hand, the evaporation mode of the thin liquid film will be transformed into the pool boiling mode, which will reduce the heat transfer performance. Therefore, the high or low filling rate will affect the heat dissipation performance of the isothermal plate.
(4) Spherical copper powder sintered plate with regular shape has the best performance, while dendritic copper powder sintered plate has relatively high thermal resistance.
(5) The heat source area has a great influence on the thermal resistance of the plate. Under the same heating power, the thermal resistance of the small area heat source is much higher than that of the large area heat source; Moreover, the thermal resistance of copper powder sintered copper plate is lower than that of pure copper plate under the two heat sources.
References:
1. Tang, Y., Tang, H., Li, J., Zhang, S., Zhuang, B., & Sun, Y. (2017). Experimental investigation of capillary force in a novel sintered copper mesh wick for ultra-thin heat pipes. Applied Thermal Engineering, 115, 1020-1030. https://doi.org/10.1016Zj.applthermaleng.2016.12.056
2. Hu, J., Yuan, W., Yan, Z., Zhou, B., Tang, Y., & Li, Z. (2015). Fabricating an enhanced stable superhydrophobic surface on copper plates by introducing a sintering process. Applied Surface Science, 355, 145-152. https://doi.org/10.10167j.apsusc.2015.07.085
3. Lewis, R., Liew, L. A., Xu, S., Lee, Y. C., & Yang, R. (2015). Microfabricated ultra-thin allpolymer thermal ground planes. Science Bulletin, 60(7), 701-706. https://doi.org/10.1007/s11434-015-0760-9
4. Li, J., & Lv, L. (2016). Experimental studies on a novel thin flat heat pipe heat spreader. Applied Thermal Engineering, 93, 139-146. https://doi.org/10.1016/j.applthermaleng.2015.09.038
5. Lv, L., & Li, J. (2017). Effect of charging ratio on thermal performance of a miniaturized two-phase super-heat-spreader. International Journal of Heat and Mass Transfer, 104, 489-492. https://doi .org/10.1016/j.ijheatmasstransfer.2016.08.087
Бюллетень науки и практики /Bulletin of Science and Practice Т. 7. №5. 2021
https://www.bulletennauki.com https://doi.org/10.33619/2414-2948/66
6. Weibel, J. A., Kousalya, A. S., Fisher, T. S., & Garimella, S. V. (2012, May). Characterization and nanostructured enhancement of boiling incipience in capillary-fed, ultra-thin sintered powder wicks. 13th InterSociety Conference on Thermal and Thermomechanical Phenomena in Electronic Systems, IEEE. 119-129. https://doi.org/10.1109/ITHERM.2012.6231422
Список литературы:
1. Tang Y., Tang H., Li J., Zhang S., Zhuang B., Sun Y. Experimental investigation of capillary force in a novel sintered copper mesh wick for ultra-thin heat pipes // Applied Thermal Engineering. 2017. V. 115. P. 1020-1030. https://doi.org/10.1016Zj.applthermaleng.2016.12.056
2. Hu J., Yuan W., Yan Z., Zhou B., Tang Y., Li Z. Fabricating an enhanced stable superhydrophobic surface on copper plates by introducing a sintering process // Applied Surface Science. 2015. V. 355. P. 145-152. https://doi.org/10.1016/j.apsusc.2015.07.085
3. Lewis R., Liew L. A., Xu S., Lee Y. C., Yang R. Microfabricated ultra-thin all-polymer thermal ground planes // Science Bulletin. 2015. V. 60. №7. P. 701-706. https://doi.org/10.1007/s11434-015-0760-9
4. Li J., Lv L. Experimental studies on a novel thin flat heat pipe heat spreader // Applied Thermal Engineering. 2016. V. 93. P. 139-146. https://doi.org/10.1016/j.applthermaleng.2015.09.038
5. Lv L., Li J. Effect of charging ratio on thermal performance of a miniaturized two-phase super-heat-spreader // International Journal of Heat and Mass Transfer. 2017. V. 104. P. 489-492. https://doi .org/10.1016/j.ijheatmasstransfer.2016.08.087
6. Weibel J. A., Kousalya A. S., Fisher T. S., Garimella S. V. Characterization and nanostructured enhancement of boiling incipience in capillary-fed, ultra-thin sintered powder wicks // 13th InterSociety Conference on Thermal and Thermomechanical Phenomena in Electronic Systems. IEEE, 2012. P. 119-129. https://doi.org/10.1109/ITHERM.2012.6231422
Работа поступила Принята к публикации
в редакцию 09.04.2021 г. 13.04.2021 г.
Ссылка для цитирования:
Jiang Weiyu, Sun Lili, Mao Jijin, Zhang Donghui, Levtsev A. Study on Heat Transfer Performance of Non-integral Capillary Core Sintered Uniform Plate // Бюллетень науки и практики. 2021. Т. 7. №5. С. 292-301. https://doi.org/10.33619/2414-2948/66/28
Cite as (APA):
Jiang, Weiyu, Sun, Lili, Mao, Jijin, Zhang, Donghui, & Levtsev, A. (2021). Study on Heat Transfer Performance of Non-integral Capillary Core Sintered Uniform Plate. Bulletin of Science and Practice, 7(5), 292-301. https://doi.org/10.33619/2414-2948/66/28
