CC BY
6
2021. 17(3). 248-260 Строительная механика инженерных конструкций и сооружений Structural Mechanics of Engineering Constructions and Buildings
ISSN 1815-5235 (Print), 2587-8700 (Online)
http://journals.rudn.ru/structural-mechanics
DOI 10.22363/1815-5235-2021-17-3-248-260 UDC 627:624.01
RESEARCH ARTICLE / НАУЧНАЯ СТАТЬЯ
Innovation structures of very lean roller compacted concrete dams Yury P. Lyapichev
Hydroproject Institute (Joint Stock Company), 2 Volokolamskoe Shosse, Moscow, 125993, Russian Federation International Commission on Large Dams (ICOLD), 61 Kleber Ave., Paris, 75016, French Republic [email protected]
Article history
Received: March 16, 2021 Revised: May 30, 2021 Accepted: June 5, 2021
For citation
Lyapichev Yu.P. Innovation structures of very lean roller compacted concrete dams. Structural Mechanics of Engineering Constructions and Buildings. 2021;17(3):248-260. http://dx.doi.org/10.22363/1815-5235-2021-17-3-248-260
Abstract. Over the past 20 years, rolled compacted concrete (RCC) dams have continued to be built in many countries because of their technical and economic advantages over conventional dams of vibrating concrete and embankment dams. The aim of this study is the development of new structural and technological solutions in RCC dams in order to reduce the consumption of cement and expand their use on non-rock foundations, which will allow them to successfully compete with concrete face rockfill dams. The numerical analyses of static and seismic stress-strain state (SST) of gravitational dams in roller compacted very lean concrete dams have been made, as well as their stability, strength and cost have been assessed. For rock and dense sandy-gravel foundations the most economical is the concrete face rockfill dam and symmetrical RCC dam of very lean concrete with bases (0.5-0.7) of both slopes and outer zones of conventional concrete and central zone of rockfill strengthened by cement-ash mortar. Taking into account that the cost of diversion and spillway tunnels for very lean RCC dam will be less and the construction period - shorter than for the concrete face rockfill dam, it can be concluded that variant of symmetrical RCC dam of very lean concrete is the technically and economically effective. Symmetrical RCC dams of very lean concrete with 1V/(0.5-0.7)H slopes have more seismic resistance and technical and economic efficiency as compared with conventional gravitational RCC dams and other types of dams. These dams up to 200 m high can be built on rock foundations and up to 100 m high - on dense sandy gravel foundations.
Keywords: very lean roller compacted concrete, dams, strengthened by cement rockfill, geomembrane, stress-strain state
Инновационные конструкции плотин из особо тощего укатанного бетона Ю.П. Ляпичев
АО «Институт "Гидропроект"», Российская Федерация, 125993, Москва, Волоколамское шоссе, д. 2 Международная комиссия по большим плотинам (ICOLD), Французская Республика, 75016, Париж, Avenue Kleber, 612 [email protected]
История статьи Аннотация. В последние 20 лет плотины из укатанного бетона (УБ) про-
Поступила в редакцию: 16 марта 2021 г. должают строить во многих странах ввиду их технико-экономических пре-Доработана: 30 мая 2021 г. имуществ по сравнению с обычными плотинами из вибрированного бетона
Принята к публикации: 5 июня 2021 г. и грунтовыми плотинами. Цель исследования - разработать новые конструк-
Yury P. Lyapichev, expert for foreign projects, member of the ICOLD, Doctor of Technical Sciences, Professor; eLIBRARY SPIN-code: 3096-6362, ORCID: https://orcid.org/0000- 0003-3750-3165
Ляпичев Юрий Петрович, эксперт по зарубежным проектам, член Комитета СИГБ по компьютерным аспектам расчета и проектирования плотин, доктор технических наук, профессор; eLIBRARY SPIN-код: 3096-6362, ORCID: https://orcid.org/0000- 0003-3750-3165
© Lyapichev Yu.P.. 2021
/^n 0 i This work is licensed under a Creative Commons Attribution 4.0 International License https://creativec0mm0ns.0rg/licenses/by/4.Q/
Для цитирования
Ляпичев Ю.П. Инновационные конструкции плотин из особо тощего укатанного бетона // Строительная механика инженерных конструкций и сооружений. 2021. Т. 17. № 3. С. 248-260. http://dx.doi.org/10.22363/1815-5235-2021-17-3-248-260
тивно-технологические решения в плотинах из УБ с целью снижения расхода цемента и расширения их применения на нескальных основаниях, что позволит им успешно конкурировать с грунтовыми плотинами с экранами из железобетона. Выполнены численные расчеты статического и сейсмического напряженно-деформированного состояния гравитационных плотин из особо тощего укатанного бетона, а также оценка их устойчивости, прочности и стоимости. Наиболее экономичными для скального и плотного песчано-гравелистого оснований являются грунтовая плотина с экраном из железобетона и симметричная плотина с заложением откосов 0,5-0,7 с наружными зонами из особо тощего укатанного бетона и центральной зоной из камня, упрочненного цементно-зольным раствором. Учитывая, что стоимость отводящих и водосбросных туннелей при плотине из особо тощего укатанного бетона будет меньше, а срок строительства - короче, чем при грунтовой плотине с экраном из железобетона, можно сделать вывод о технико-экономической эффективности варианта плотины из особо тощего укатанного бетона. Плотины симметричного профиля из особо тощего укатанного бетона с заложением обоих откосов 0,5-0,7 обладают более высокой сейсмостойкостью и технико-экономической эффективностью по сравнению с обычными гравитационными плотинами из УБ и другими видами плотин. Плотины данного типа высотой до 200 м можно строить на скальных основаниях, а высотой до 100 м - на плотных песчано-гравелистых основаниях.
Ключевые слова: плотины, особо тощий укатанный бетон, упрочненный цементом камень, геомембрана, напряженно-деформированное состояние, сейсмостойкост
Introduction
In most countries of the world when designing gravity dams from conventional and RCC use two main conditions of strength (M. Levy and O. Hoffman), written in the following form respectively:
a(B) - ywH > at, (1)
da(B) / dat > 0, (2)
where a(B) - total vertical normal stress (compression with sign "-") in point B (at the end of open crack, Figure 1, b; Yw - density of water; H- head; at - tensile strength of RCC in seams; at - crack length in upstream face.
In crack (opened "cold" seam) there is complete uplift water pressure and shear resistance in RCC seam is absent. The first condition (1) means that the effective normal stress in point B does not exceed the tensile strength of RCC in seams (approximately equal to cohesion) and then the AB crack does not develop (seam opening does not occur).
Equation (1) requires knowledge of stresses a(B), which is not determined by the equilibrium equations alone. According to the theory of eccentric compression, which is not applicable, especially for the contact section, the distribution of total vertical stresses will be linear from point B to the downstream face, i.e. in closed (work) zone of RCC seam (Figure 1, b). For this RCC dam profile and the operating loads, the stress in point B depends on coefficient a of relative depth of crack propagation (a = AB / AC). With increase of a coefficient the moment from dam own weight relatively to point B increases, which leads to decrease of normal stress, while uplift water pressure increases, which leads to increase of normal stress. The balance between these two counteractions is expressed by Hoffman condition (2). If Hoffman condition (2) is not held and Levy condition (3-1) is held, then this means crack spreading or seam opening. As a coefficient increases, the tension in point B decreases, which leads to decrease of normal stresses. There may be value of a coefficient greater than given ao for which Levy condition will be held.
If both conditions (1) and (2) are not held, this means unstable crack propagation or opening of RCC seam with increase of a coefficient effective tension in point B increases. Dam failure is inevitable if Hoffman condition (2) is not held for any value of a coefficient greater than ao. The fulfillment of both conditions in designing of gravity dam of height of 100 m of conventional concrete with vertical upstream face for average values of shear strength of the rock foundation (excluding seismic loads) leads to adoption of base of downstream slope of about 0.8.
Crack zone
Monolithic zone
a b
Figure 1. Strength condition for crack appearance (joint opening) in RCC dam
Vertical stresses in foundation
ï=23KN/mS
o u (MPa)
Deflection angle of resulrant from vertical
20' 10°
22°
18°
MPa
0,40
Residual uplift pressure
Figure 2. Vertical stresses, MPa, in foundation of gravity (a) and symmetrical (b) RCC dam (h = l00 m)
a
b
Further are the given results of calculations of stability and contact stress in symmetrical dam from very lean RCC with base of downstream slope of 0.7 and in conventional gravity dam of 100 m high (on rock foundation) with lower face of 0.8. Figure 2, b presents results of calculations of boundary vertical contact stresses (in MPa), dependence of angle of deviation of resultant of all forces in dam foundation from the vertical and margin of safety in-plane shear (SF) in dam foundation from degree of residual uplift water pressure and due to drainage operation.
For comparison, Figure 2, a shows the same results of calculations and dependences for gravity dam of the same height (100 m) from conventional concrete (density 2.4 t/m2) with vertical upstream face. In rock foundation of both dam, equal shear strength is adopted (internal friction angle 9 = 30o, cohesion C = 0.3 MPa), which correspond to the criteria of Hoek for rock granite-gneisses of average weathered with crack spacing of 0.5 m. Another large difference between both dams concerns shear stresses in the contact section: in symmetrical dam from RCC the average shear stresses are much lower. than in gravity dam (0.36 vs 0.63 MPa). The angle of deviation 9 of resultant of all forces in foundation from the vertical, depending on uplift pressure u in symmetrical dam, varied from 14 to 22o whereas in gravity dam from 27 to 42o (Figure 2, a).
In 1992, P. Londe, President of ICOLD proposed an idea of solid embankment [1] from very lean RCC with a cement consumption of 50 kg/m3 in dam of symmetrical profile h = 100 m with the base of both slopes of 0.7 on rock foundation. This idea was supported by some specialists [2]. The water tightness of dam was provided by reinforced concrete face on upstream slope (Figure 3).
Figure 3. Symmetrical h = 100 m of the very lean RCC dam with reinforced concrete face
Further development of this idea led to development in 1998 [3-4] of project of symmetrical dam h = 100 m with base of both slopes of 0.5, external zones of RCC of 3rd type according to RCC classification [4] (cement consumption 70-80, fly ash 100-120 kg/m3) with width equal to (3 + 0.1H), (where H is reservoir head, m) and inner zone of rockfill, enriched or hardened with cement-ash mortar (REC) or RCC-0 (Figure 4). Advantages of symmetrical dams of very lean RCC (Figure 3) and rockfill enriched or hardened with cement-ash mortar (Figure 4) compared to conventional gravity dams from RCC are following:
1) reduction of stresses in dam body and its foundation;
2) low cost of very lean RCC and rockfill enriched with cement;
3) greater seismic resistance than that of gravity dams from RCC;
4) the possibility of construction on semi-rock foundations;
5) treatment of horizontal seams is not required;
6) small number of deformation joints with their large spacing (30-40 m);
7) drainage of dam foundation occurs due to permeability of lower layer of the inner zone REC or RCC-0, seepage uplift pressure in foundation due to grout curtain from the gallery will be small.
Water impermeability of upstream face is provided by geomembrane CARPI (Switzerland) - a two-layer film made of PVC and drainage of 3 mm thick geotextile (Figure 4). Installation of strips of film with 2.1 m width is carried out independently and in parallel with placement of RCC by platforms fixed on dam crest and descending along upstream face along the rails. The lower end of film is anchored in concrete apron in foundation of upstream face and upper end is anchored in dam crest on steel plates and bolts (Figure 5). The impermeability of film joints and fasteners is provided by rubber seals and smearing of joints with epoxy glue.
2x0,3 = 0,6m
Figure 4. Symmetrical dam with outer zones of RCC (type 3) from 30 cm thick layers and inner zones of rockfill enriched with cement-ash mortar (REC or RCC-0) from 60 cm thick layers
Typical cross sections: a - RCC layers; b - water-proof geomembrane; c - vertical anchorage and drainage of geomembrane; d - drain-box of contour system of drainage area; e - contour sealing; f - contour slab-apron; g - ventilation pipe
I
b-
d
sv
Contour slab-apron (f): h - drainage canal;
i - grout curtain; j - contact grouting; k - gallery
Vertical anchorage and drain-age of geomembrane (c): 1 - embedded profile; 2 - profile-bracing; 3 - fastening system; 4 - drainage layer; 5 - waterproofing insulating tape; 6 - canal for water passing
Figure 5. Geomembrane CARPI of upstream face of RCC dams
The CARPI geomembrane is installed and successfully operated on 37 dams from the RCC [5-8]. It is characterized by high reliability from punctures, water resistance, high drainage capacity and is recommended for use in these dams in ICOLD Bulletin 135 (2010) [9].
Methods
Methodology of numerical modeling of seismic resistance of dam taking into account the possibility of opening of technological seams
When numerically assessing of seismic resistance of system "dam - foundation - reservoir" system of equations of motion is to be solved:
[K] {U} + [C] {V} + [M] {W} = {R(t)}, (3)
where [K], [C], [M] - matrix of stiffness, damping and masses of calculation area; {U}, {V}, {W} - vectors of relative displacements, velocity and acceleration in fixed points of calculation area; {R(t)} - vector of variable dynamic actions.
Solution of system of equations (3) is made according to method used in analyses of dams from conventional concrete. These analyses did not take into account the influence of gravitational waves and simplified the boundary conditions between reservoir and dam and reservoir and dam foundation at these boundaries the condition of equality of movements normal to these boundaries, both for solid body (dam, foundation) and water, is fulfilled. Transmission of tangential stresses at these boundaries is taken into account, which simplifies the task by abandoning introduction of contact elements. To describe behavior of RCC an elastic plastic (with hardening) model of conventional concrete used in seismic analyses of concrete dams was used, in which shear parameters of RCC seams were adopted (internal friction angle 9 = 45°, cohesion C, tensile strength across seam p = C). Description of RCC deformability in the model is made by piecewise smooth loading surface separating the area of elastic operation of RCC in stress space from the stress change area in which plastic deformations are developing. Introduction of loading surface defines the concepts of loading, unloading and neutral loading.
Complete deformations consist of viscoelastic and plastic deformations. In analysis of viscoelastic and plastic deformations the flow law associated with loading function from Mises maximum principle is used:
dsvpy = dXtdfr / day. (4)
For system of determining parameters tangent and normal stresses on maximum shear site are accepted
Tv = (ai - a2) / 2; av = (ai + a2) / 2. (5)
Hardening parameters are shear and volumetric pseudoplastic deformations on maximum shear site
Yvp = (s^ + s2p) / 2; 0vp = (evp + s2p )/2. (6)
Loading functions of the model are formulated on the basis of analysis of available experimental data of RCC as follows
Tv = av - p. (7)
Equation (7) reflects the destruction of RCC with predominance of tensile stresses, equation (6) - behavior of RCC in case of its destruction from compressive stresses.
The RCC model allows to reproduce in analyses the appearance of horizontal cracks in dam (opening of RCC seams) and in dam foundation - arbitrary cracks and subsequent work of RCC in crack zone only for compression.
Results of analyses and its discussion
Analyses of stability, strength and cost ofRCC dams
Below are given results of analyses of stability and strength of 4 types of dams h = 100 m: gravity dam from RCC-3rd type (Figure 6), rockfill dam with reinforced concrete face, dam from very lean RCC (Figure 3) and dam from RCC and rockfill enriched with cement-ash mortar (Figure 4). The rock foundation (angle of inner friction 9 = 45o, cohesion C = 1 MPa) was considered in all variants, non-rock foundation 9 = 30o, C = 0.3 MPa) in variants 2-4. These analyses took into account the earthquake intensity on the MSK-81 scale of 8 grade (acceleration 0.2g).
Variant 1 (Figure 6): gravity RCC dam with downstream face with the base of 0.8 and upstream face with the base of 0.1, crest width of dam - 8 m. Uplift water pressure in dam foundation is taken into account its decrease in drainage by 35%. Parameters of shear strength in RCC seams: 9 = 45o, C = 2 MPa. Seismic resistance of the dam was determined by the pseudostatic method [28].
Variant 2: rockfill dam with with reinforced concrete face, the base of upstream slope 1.4, the base of downstream - 1.5, crest width of dam - 8 m. The shear strength of rockfill: 9 = 45o, C = 0. Seismic resistance of both slopes was determined by the pseudostatic method of Terzaghi - VNIIG.
Variant 3 (Figure 4): symmetrical dam with outer zones from RCC-3 and inner zone from rockfill, enriched with cement-ash mortar with base of both slopes 0.5 with upstream face of geomembrane CARPI. Parameters of shear strength in RCC seams: 9 = 45o, C = 0.5 MPa, in rockfill, enriched with cement-ash mortar: 9 = 45o, C = 0.1 MPa. Uplift water pressure in drainage is decreased by 40%.
Variant 4 (Figure 3): symmetrical dam from very lean RCC with face of reinforced concrete (base of both slopes 0.7). Parameters of shear strength in RCC seams: 9 = 45o, C = 0.5 MPa. Uplift water pressure in drainage is decreased by 40%.
Calculations of cost of all dam variants (for running meter) were made by unit prices (for 1 m3) in 1995, given in [10].
As criteria for the stability of RCC dams the safety factor for in-plane shear (SF) in dam foundation or for round-cylindrical sliding (in variant 2) and tg0 (0 - angle of deviation of resultant of all forces in dam foundation from the vertical), normal vertical stresses oy: tensile (+) and compressive (-) were used. Results of analyses of seismic resistance and cost of 1 running meter of dam is given in Table. 3.1 and 3.2 for both dam foundations [10]. As can be seen from Tables 1 and 2 the most economical for rock and sand-gravel foundations will be: variant 2 (rockfill dam with reinforced concrete face) and variant 4 (symmetrical dam with outer zones of RCC-3 and inner zone of rockfill enriched or hardened with cement-ash mortar).
Normal operation 100.0 m J level
8 m
Figure 6. Gravity dam from RCC-3
Table 1
Results of analyses of stability, stresses and cost of dams on rock foundation
Cost, thous. doll. per running m Dam variant SF (tg0) whithout seism SF (tg0) with seism CTj, MPa, whithout seism g>, MPa, with seism
140 1 3.0 (0.7) 1.85(1.16) <0 +1.2
91 2 1.4 1.2 - -
115 3 4.3 (0.23) in D-S 3.3 (0.34) in U-S 2.7 (0.43) in D-S 2.1 (0.58) in U-S -1.03 in D-S -1.56 in U-S -0.74 in D-S -1.78 in U-S
155 4 4.8 (0.21) in D-S 3.7 (0.29) in U-S 2.9 (0.32) in D-S 2.3(0.48) in U-S <0 <0
Note: D-S - downstream slope; U-S - upstream slope or face.
Results of analyses of stability, stresses and cost of dams on soil foundation Table 2
Cost, thous. doll. per running m Dam variant SF (tg0) whithout seism SF (tg0) with seism CTy(-), MPa, whithout seism CTy(-), MPa, with seism
91 2 1.4 1.2 - -
115 3 2.8 (0.32) in D-S 2.1 (0.39) in U-S 1.51 (0.56) in D-S 1.16 (0.82) in U-S -1.12 in D-S -1.67 in U-S -0.8 in D-S -1.9 in U-S
155 4 3.0 (0.28) in D-S 2.3 (0.42) in U-S 1.57 (0.53) in D-S 1.20 (0.8) in U-S -0.9 in D-S -1.4 in U-S -0.6 in D-S -1.8 in U-S
Note: D-S - downstream slope; U-S - upstream slope or face.
Given that the cost of diversion and spillway tunnels in variants 3 and 4 will be much less, and the construction time will be shorter than in variant 2 approximately by half a year or a year, it can be concluded about cost effectiveness of variants 3 and 4 of RCC dams.
Stability and strength of RCC dams for static and seismic loads
Tables 3 and 4 show stability and safety factors for in-plane shear on foundation of conventional gravity dam from RCC-3 (h = 100 m) with vertical upstream face and downstream face with bases 0.7; 0.8; 0.9 and symmetrical RCC-3 and RCC-0 (h = 100 m) with bases of both slopes 0.5 and 0.7.
Both dams are located on rock (9 = 40o, C = 0.2 MPa) and dense sandy-gravel (9 = 35o, C = 0) foundations. In analyses the uplift water pressure along the axis of grout curtain (on rock foundation) or wall curtain (on soil foundation) in 40% of water pressure was taken. Analyses of seismic stability of the dam were carried out according to the linear-spectral theory (LST).
Table 3
Coefficients of stability factor on shear of gravity dam from RCC-3 (h = 100 m)
Coefficients of stability factor of dam on shear (static/seismic) for bases of downstream slope
Type of foundation -
_0.7_0.8_0.9_
Rock 1.91/1.47 2.14/1.60 2.37/1.73
Sandy gravel 1.33/1.02 1.50/1.12 1.66/1.21
Table 4
Coefficients of stability factor on shear of symmetrical dam from RCC (h = 100 m) for various foundations
Coefficients of stability factor of dam on shear (static/seismic) for bases of both slopes Type of foundation -
_0.5_0.7_
Rock 3.15/2.21 4.27/2.74 Sandy gravel_2.20/1.55_2.98/1.92_
Comparison of Tables 3 and 4 with normative stability coefficients of concrete dams of class I, equal in static and seismic cases 1.32 and 1.18 respectively, shows that seismic resistance of gravity dam (bases upstream slope of 0.7-0.8) is insufficient on sandy-gravel foundation. In this case, it is necessary to change the usual dam profile to symmetrical one of RCC-0 and RCC-3 with bases of both slopes of 0.5-0.7 (Figures 3 and 4).
Analyses of 100 m high symmetrical dam (from RCC-3 andRCC-0) on action of powerfull earthquake accelerograms
In these analyses the same parameters of shear strength of RCC-3 and RCC-0 were used as in previous analyses of seismic resistance within LST framework and parameters of deformability of rock foundation (E = 10000 MPa and u = 0.2).
Symmetrical dam analyses of RCC-3 and RCC-0 for 100 m high dam with bases of both slopes of 0.5 for action of the earthquake accelerogram with horizontal acceleration of 0.2g and vertical one of 0.14g showed that for magnitude 8 of earthquake the dam works elastically and quite reliably and its movements completely fade by the end of earthquake.
Figure 7 shows the mesh of finite elements (FE) of dam with one short crack (seam opening) in foundation of upper zone RCC-3. With horizontal acceleration of 0.4g and vertical one of 0.28g, the dam reaction in its foundation is elastic with complete damping of oscillations, in upper part the dam reaction is elasto-plastic. The picture of opening seams of RCC (Figure 8) shows that in dam foundation the depth of seams opening from reservoir side reaches the middle of dam profile and from downstream side reaches its quarter. Taking into account availability of CARPI membrane on upstream slope the uplift water pressure in opened seams of RCC is excluded and the seismic resistance of dam is ensured.
Figure 7. Mesh of FE and joint opening (bold line) Figure 8. Mesh of FE and joint opening (bold line)
in base of upstream zone of the RCC-3 in base of upstream zone of the RCC-3
for earthquake of magnitude 8 (Ahoriz = 0.2g, Avert = 0.14g) for earthquake of magnitude 9 (Ahoriz = 0.4g, Avert = 0.28g)
Thus, symmetrical dam of h = 100 m (bases of both slopes of 0.5) has sufficient factor of seismic resistance during earthquake of magnitude 8 and 9, which indicates expediency of its consideration in dam projects in seismic areas of Russia, CIS countries and foreign countries. At present the optimization of structures and technologies of construction of traditional RCC dams [11-23] and competing with these dams rockfill dams with reinforced concrete faces [24-27] continues.
Examples of new symmetrical dams from very lean RCC Cindere 107 m high dam in Turkey
In 2005 Cindere dam was built in Turkey, the highest (107 m) and largest (the volume of RCC is 1.5 million m3, the total volume of concrete is 1.7 million m3) dam of this type. Feature of dam layout is arrangement on its downstream slope the operated spillway and water intake of hydropower power plant (Figure 9). The spillway central section of dam has base of downstream slope increased to 0.89 for favorable interface with the apron slab. The spillway with 4 holes of 10 m wide and 12.5 m high, overlapped by segment gates is designed to pass 3620 m3/sec. The profile of Cindere dam is symmetrical with base of both slope of 0.7. Figure 10 show the stages of its construction given in [20]. The dam is located on semi-rock foundation of aspid shales with dry compressive strength (5-24) MPa and deformation module (1-7)104 MPa. In the dam particularly rigid RCC-1 was used with consumption of cement 50 and fly ash of 20 kg/m3, thickness of layers of RCC - 25 cm. Watertight-ness of upstream slope was provided by precast concrete panels with PVC film fixed on them, which cannot be considered successful due to danger of its punctures during mounting.
The dam stability to shear in its foundation and seams in RCC was ensured for maximum horizontal acceleration of 0.4g. Compressive stresses were provided on upstream slope of the dam and its foundation, ensu-
ring that there is no opening of contact seam in foundation and seams of RCC. Due to the high seismicity RCC seams on the upstream side were treated with layer of cement mortar 25 mm thick to depth of 13 m in the bottom of upstream slope and 5 m in dam crest, which ensured high cohesion between RCC cold layers. The construction period of the dam was 34 months, which corresponds to the average monthly intensity of placement of RCC of 50 thousand m3. At present 3 project of such dams are being considered in Turkey.
Figure 9. Plan of Cindere hydroscheme with RCC-1 dam, spillway and hydropower plant building (dam crest length - 280 m) [20]
a b
Figure 10. Top (a) and upstream (b) views of Cindere dam [20]
Ituango dam of height 180 m in Colombia
In 1999 energy company ISAGEN (Medellin) invited the author of article to conduct expertise of the feasibility study of the dam project. In the feasibility study rockfill dam with reinforced concrete face was adopted as main variant, which was used in many dam projects in Colombia.
Instead of this dam variant by our recommendation was developed symmetrical gravity dam from RCC-2 with bases of both slopes of 0.7, height of 180 m, length along the dam crest of 450 m, RCC volume of 2.4 million m3 with surface spillway (Figure 11), which allows to abandon spillway tunnels, significantly accelerates the total dam construction time and reduces its cost [3]. The dam is able to resist earthquake of 9 magnitude without opening of RCC seams and dynamic loads when flood of 21.000 m3/sec passes through operating spillway with 21.7 m head (with smooth spillway face and jet throw in downstream zone). The head of spillway was made of reinforced concrete, non-overflow part of dam crest has curved surface to reduce stress concentrations during the earthquake. Composition of RCC-2 (per 1 m3): cement 100-120 kg, crushed stone - 1250 kg, pebble gravel - 1000 kg. Due to wide dam profile the treatment of cold seams of RCC with cement mortar is assumed only in pressure and upper zones of the dam. The dam profile includes 33 m high upstream coffer dam with grout gallery on its crest, which will accelerate the dam construction.
Figure 11. Profile of spillway section of RCC-2 Ituango dam, H = 180 m
Yumaguzinskaya dam from very lean RCC (65 m high, Russia, project variant)
When designing this hydraulic system we developed variant of dam 65 m high and 600 m length from very lean RCC on soft foundation. Technical and economic advantages of this dam variant in comparison with accepted variant of rockfill dam: 1) arrangement of regulated spillway in channel part of dam, which allows to abandon bank side spillway; 2) allowing overflow of peak of catastrophic flood over dam crest, which reduces level of Surcharged Reservoir Level (SRL) and flooding of downstream area; 3) lower cost and construction time. Analyses of stability and strength of spillway dam (bases of both 0.7) in channel of gravel-pebble deposits for static and seismic loads (7 grade) showed high stability and strength of dam and its foundation with uniform diagram of vertical stresses in foundation. Figures 12 and 13 show symmetrical profiles of spillway and non-overflow dam sections from very lean RCC. In foundation of both sections from upstream gallery were made trench walls-curtains (15 m deep in channel and up to 70 m on right bank).
Figure 12. Spillway section of Yumaguzinskaya from very lean RCC: 1 - watertight reomembrane; 2 - channel deposits; 3 - trench wall-curtain; 4, 5 - semi-rock deposits; &ny - surcharged reservoir level; Hny - normal reservoir level; Pny - rated reservoir level; RCC - RCC type 2; REC - rockfill, strengthened by cement-ash mortar; CVC - conventional vibrating concrete
6 6
Figure 13. Non-overflow section of Yumaguzinskaya dam from very lean RCC: 1 - CARPI membrane; 2 - precast concrete blocks; 3 - gravely sands; 4 - trench cut-off wall; 5 - drainage holes; 6 - bed rock;
CVC - conventional concrete; RCC-1 - RCC type 1; REC - rockfill, strengthened by cement-ash mortar
Conclusion
Dams of symmetrical profile of very lean RCC with bases of both slopes 0.5-0.7 have higher seismic resistance and technical and economic efficiency compared to conventional gravity dams from RC C and other types of dams.
These dams up to 200 m high can be built on rock foundations and up to 100 m high on dense sandy-gravel foundations.
The possibility of building these dams in seismically active areas of Russia, CIS countries, Latin America and Asia, as well as in Russian dam projects abroad should be considered.
References
1. Londe P. The faced symmetrical hardfill dam: a new concept for RCC. Intern. Water Power and Dam Construction. 1992:19-24.
2. Jinsheng J., Cuiying Z., Zhenkun D. Cemented material dams and their application. Hydropower and Dams. 2015; 22(6):64-67.
3. Lyapichev Yu. Presas de concreto compactado con rodillo (CCR) y presas mixtas de CCR y escollera (Aspectos de Diseño y Construcción). Seminar sobre presas de CCR. Medellin, Colombia: Compania ISAGEN; 1998. p. 102.
4. Lyapichev Yu.P. Design, construction and behavior of modern high dams. Part 1. Dams made of rolled concrete. Saarbrücken: Palmarium Academic Publish; 2013. (In Russ.)
5. Kalpakci V., Bonab A.T., Ozkan M.Y. Experimental evaluation of geomembrane/geotextile interface as base isolating system. Geosynthetics Intern. 2018;25(1):1-11. https://doi.org/10.1680/jgein.17.00025
6. Yang P., Xue S.B., Song L., Zhu X.W. Numerical simulation of geomembrane wrinkle formation. Geotextiles and Geomembranes. 2017;45(6):697-701. https://doi.org/10.1016/j.geotexmem.2017.08.001
7. Giroud J. Leakage control by geomembranes. Soils and Rocks. 2016;3:213-235.
8. Moutafis N., Thanopoulos Y. Geomembrane faced hardfill dam. Hydro 2015. Bordeaux, France; 2015.
9. ICOLD Bulletin 135. Geomembrane sealing systems for dams. 2010.
10. Blinder S., Toniatti N. RCC and CFR Dams. Cost Comparision, Intern. Symposium on RCC Dams, Santander, Spain. 1995:71-83.
11. Cervera M., Oliver J., Prato T. Simulation of construction of RCC dams. Part II: stress and damage. Journal of Structural Engineering. 2000;126(9):1062-1069. https://doi.org/10.1061/(asce) 0733-9445(2000)126:9(1062)
12. Zhang X., Li S., Li Y., Ge Y., Li H. Effect of superficial insulation on RCC dams in cold regions. Advances in Engineering Software. 2011;42:939-943. https://doi.org/10.1016/j.advengsoft. 2011.06.004
13. Tamagava S. Toubetsu dam: example of innovative CSG technology. Hydropower and Dams. 2012;19(3):64-67.
14. Fujisawa T., Sasaki T. Development of the trapezoidal CSG dam. Hydropower and Dams. 2012;19(3):58-63.
15. Kuzmanovic V., Savic L., Mladenovic N. Computation of thermal-stresses and contraction joint distance of RCC Dams. Journal of Thermal Stresses. 2013;36(2):112-134. https://doi.org/10.1080/ 01495739.2013.764795
16. Mohamed I. Investigating the possibility of constructing low cost RCC dam. Alexandria Engineering Journal. 2014;53(1):131-142. https://doi.org/10.1016/j.aej.2013.11.009
17. Gu Q., Yu C., Lin P., Ling X., Tang L., Huang S. Performance assessment of a concrete gravity dam at Shenwo reservoir of China using deterministic and probabilistic methods. International Journal of Structural Stability & Dynamics. 2014;14(05):1440002. https://doi.org/10.1142/S0219455414400021
18. Du C.B., Wu S.Y., Zhang S.R. Full-scale dynamic simulation and visualization for structure safety and schedule coupling of RCC gravity dams. 2017 International Conference on Smart Grid and Electrical Automation (ICSGEA). 2017;1:481-487. https://doi.org/10.1109/ICSGEA.2017.96
19. Wanga L., Yang H.Q., Zhou S.H., Chen E., Tang S.W. Mechanical properties, long-term hydration heat, shink-age behavior and crack resistance of dam concrete designed with low heat Portland (LHP) cement and fly ash. Construction and Building Materials. 2018;187:1073-1091. https://doi.org/10.1016/j.conbuildmat.2018.08.056
20. Batmaz S. Cindere dam - 107 m high RCC dam (RCHD). Proceedings of IVInternational Symposium on RCC Dams, Madrid, Spain. 2003;1:121-126.
21. Bayagoob K., Bamaga S. Construction of roller compacted concrete dams in hot arid regions. Materials. 2019;12(19):3064. https://doi.org/10.3390/ma12193064
22. ICOLD Bulletin 177. Roller compacted concrete dams. 2020.
23. Aniskin N.A., Shajtanov A.M. Low-cement concrete dams: construction, structures and innovations. Vestnik MGSU. 2019;15(7):1018-1029. (In Russ.) https://doi.org/10.22227/1997-0935.2020.7.1018-1029
24. Sainov M.P., Shigarov A.Yu., Yasafova S.A. Reinforcement impact on the stress-deformation state of concrete faced rockfill dam. Vestnik MGSU. 2019;14(3):347-355. (In Russ.) https://doi.org/10.22227/1997-0935.2019.3.347-355.
25. Hu K., Chen J., Wang D. Shear stress analysis and crack prevention measures for a concrete face rockfill dam, advanced construction of a first-stage face slab, and a first-stage face slab in advanced reservoir water storage. Advances in Civil Engineering. 2018;2018:2951962. https://doi.org/10.1155/2018/2951962
26. Sukkarak R., Pramthawee P., Jongpradist P., Kongkitkul W., Jamsawang P. Deformation analysis of high CFRD considering the scaling effects. Geomechanics and Engineering. 2018;14(3):211-224. https://doi.org/10.12989/gae.2018.14.3.211
27. Glagovsky V.B., Radchenko V.G. New trends in the construction of ground dams. Gidrotekhnicheskoe Stroitel'stvo. 2013;(1):2-8. (In Russ.)
28. SNiP. 33-03. Hydraulic structures in seismic regions. Moscow: State Building Committee of Russia; 2003. (In Russ.)
