CC BY
10For citation-. Hu Ze-Kui. Double-sided layout stamping thick plate feeding system //
URL: http.//rectors.altstu.ru/ru/periodical/archiv/2022/2/articles/2_2.pdf EDN. https://elibrary.ru/khhwfh
UDK 67.05
Double-sided layout stamping thick plate feeding system
mm12
1 «ifg^gsmm 430073
2 ^n 431700
E-mail: 814400892@qq.com
0
[1]. X^tmix«^!^-
xtmumwm mmu, sx^-^temm,
#№mM±mmw^Tmmw^, mmi
^¡^fa, [2].
m-m mmmMmmw.-mmmm.mMt ^m, m^±Tm, mm^ft^&Mwmxft&m [3].
Mrnwwi^mmmmmmmrn 1 mm^mmm 2 3 rn^, mu (3) w^mwxxTmmw^mg. w (4) ^mw^itmmw^w^ (2), /xxia ^rnmw (5) mmi^^ ^±mu, i®m 4 rn^. m^ (i) ^mu^mmmwi^ma. a&^&^&m w (6) ^TO^mw (7) a^^^mm^.
wm^m^, mummrnmw, mmmmm^maftRmnm, sp^mu BMffiwm. wm^m, m«mt№mfjM^w^w, a&±rmmw^
M^mw, mm-m
m i
l) ffi^; 2) 3) mU; 4) 5) ^M^S;
6) 7)
Fig. l. Stamping feed system l) Push block; 2) Support wheel; 3) Thick plate; 4) Loading and unloading clamping device; 5) Locating fixture; 6) Movable clamping device; 7) Fixed clamping device
mu (i) ^^ (2) re^a ^mmtmsmrn,
mmm^s (4) wMmu. (3) ^mmsmfarnm 180°. m
m. № 2
a 2 siit^s
l) mu; 2) 3) 4) Sli^M^S;
Fig. 2. Turning device l) Thick plate; 2) Guide wheel; 3) Flip rollers; 4) Flip clamping device
Fig. 3. Initial position map of thick plate
m 4 шт
Fig. 4. Feed chart
2 жшшжх
[4]. втшшшш ^^хтш, -шпн^-^пп, шшшШМШШШЯ [5]. жш шштхжшт, ттшттт.
вяшш, ЙХГ^НЩМФ , ты^&тш^птжттш ф [6].
2000mm, Ш 250mm, Ш 15mm ШШ^Ш, 400mm, й
200mm
т з, т 4
400X200
ты = ^ЦЦе x ioo% = =X=X1XX5 X 100% = 32% (1)
жшшшшштшт:
400X200
«Ж^ = ^ИИ^ X 100% = X 100% = 56% (2)
шшадйм^^шшадад^ 32%, тжшшттп 56%, ш
тшшшящшм 20%. тмттттт.
Fig. 3. Schematic diagram of single-sided layout waste
Fig. 4. Schematic diagram of double-sided layout waste
4 ШШ
п. m жштшттшштшхтт^т. шттшш
[1] 2020 ^ШП'ФШ^, ШШМШШШ^ [J]. ШЙ^ДОН, 2021(20):43-44.
[2] rnt^, ^HX^ä^Mfe^M^MÄ [J].
2006(02):18-21. DOI: 10.16316/j.issn.1672-0121.2006.02.005.
[3] m4, MI4. [J]. fe^, 2013,48(06):29-32. DOI: 10.16316/j.issn.1672-0121.2013.06.003.
[4] ^fe^Hfe^ [J]. iÄfe^, 1997(04):62-75.
[5] M^R ^MM««^^ [J]. 2004,16(07):890-897.
[6] 0®, . Si^t^f^I^^il^fe^^^ [J]. Ittli^Ä, 2016,23(03):103-107.
References
[1] Li Fenghua. Research Report on Technical and Economic Data of Fine Stamping Industry in 2020 [J]. Forging and Stamping, 2021(20):43-44.
[2] South Lei Ying, Qi Chunxiao, Sun Yousong. Current situation and development of automatic feeding technology in stamping production [J]. Forging Equipment and Manufacturing Technology, 2006 (02): 18-21. DOI: 10.16316/J.ISSN.1672-0121.2006.02.00.
[3] Feng Ke, Zhang Xianglin, Liu Xin, Zhou Sheng. Overall design of automation transformation of small and medium-sized stamping production lines [J]. Forging Equipment and Manufacturing Technology, 2013,48 (06): 29-32. DOI: 10.16316/J.ISSN.1672-0121.2013.06.
[4] Zhang Zhengxiu. Thick plate stamping technology [J]. Die Technology, 1997(04):62-75.
[5] Jia Zhixin. Research status and trend of nesting problem [J]. Journal of Computer Aided Design and Graphics, 2004,16(07):890-897.
[6] Xiong Xueying, Peng Qiang, Wang Yuming. Baosteel Advanced Forming Manufacturing Cost Model and Technical Route [J]. Journal of Plastic Engineering, 2016,23(03):103-107.
