Научная статья на тему 'DEVELOPMENT OF DESIGNS AND JUSTIFICATION OF THE PARAMETERS OF A SCRETTING DRUM WITH A DAMPER OF A SPINNING MACHINE'

DEVELOPMENT OF DESIGNS AND JUSTIFICATION OF THE PARAMETERS OF A SCRETTING DRUM WITH A DAMPER OF A SPINNING MACHINE Текст научной статьи по специальности «Физика»

CC BY
29
6
i Надоели баннеры? Вы всегда можете отключить рекламу.
Журнал
Science and innovation
Область наук
Ключевые слова
Spinning machine / discretizing drum / fibers / tape / gear set / shock absorber / mass / stiffness / dissipation / oscillations / amplitude / amplitude / frequency. / Прядильная машина / дискретизирующый барабанчик / волокна / лента / зубчатая гарнитура / амортизатор / масса / жесткость / диссипация / колебания / амплитуда / размах / частота.

Аннотация научной статьи по физике, автор научной работы — A. Juraev, N. Urakov

The article provides an analysis of the features of existing designs of the discretizing drum of a spinning machine. The structural scheme and the principle of operation of the recommended composite discretizing drum with a shock absorber and sectional gear sets are presented. The results of theoretical studies of vertical vibrations of sectional toothed sets of a discretizing drum. On the basis of the obtained patterns of vibrations of gear sets and the constructed graphic dependencies, the main parameters of the drum are substantiated.

i Надоели баннеры? Вы всегда можете отключить рекламу.
iНе можете найти то, что вам нужно? Попробуйте сервис подбора литературы.
i Надоели баннеры? Вы всегда можете отключить рекламу.

РАЗРАБОТКА КОНСТРУКЦИЙ И ОБОСНОВАНИЕ ПАРАМЕТРОВ ШЛИФОВАЛЬНОГО БАРАБАНА С ДЕМПФЕРОМ ПРЯДИЛЬНОЙ МАШИНЫ

В статье приводится анализ особенностей существующих конструкций дискретизирующего барабанчика прядильной машины. Представлена конструктивная схема и принцип работы рекомендуемого составного дискретизирующего барабанчика с амортизатором и секционными зубчатыми гарнитурами. Результаты теоретических исследований вертикальных колебаний секционных зубчатых гарнитур дискретизирующего барабанчика. На основе полученных закономерности колебаний зубчатых гарнитур и построенных графических завимостей обоснованы основных параметры барабанчика.

Текст научной работы на тему «DEVELOPMENT OF DESIGNS AND JUSTIFICATION OF THE PARAMETERS OF A SCRETTING DRUM WITH A DAMPER OF A SPINNING MACHINE»

UIF-2022: 8.2 SCIENCE AND INNOVATION 2022

ISSN: 2181-3337 INTERNATIONAL SCIENTIFIC JOURNAL №4

DEVELOPMENT OF DESIGNS AND JUSTIFICATION OF THE PARAMETERS OF A SCRETTING DRUM WITH A DAMPER OF A SPINNING MACHINE

Juraev Anvar Juraevich

Dr. tech. sciences, professor of Tashkent Institute of Textile and Light Industry Urakov Nuriddin Abramatovich

Assistant of Tashkent Institute of Textile and Light Industry https://doi.org/10.5281/zenodo.6969459

Abstract. The article provides an analysis of the features of existing designs of the discretizing drum of a spinning machine. The structural scheme and the principle of operation of the recommended composite discretizing drum with a shock absorber and sectional gear sets are presented. The results of theoretical studies of vertical vibrations of sectional toothed sets of a discretizing drum. On the basis of the obtained patterns of vibrations of gear sets and the constructed graphic dependencies, the main parameters of the drum are substantiated.

Keywords: Spinning machine, discretizing drum, fibers, tape, gear set, shock absorber, mass, stiffness, dissipation, oscillations, amplitude, amplitude, frequency.

РАЗРАБОТКА КОНСТРУКЦИЙ И ОБОСНОВАНИЕ ПАРАМЕТРОВ ШЛИФОВАЛЬНОГО БАРАБАНА С ДЕМПФЕРОМ ПРЯДИЛЬНОЙ МАШИНЫ

Аннотация. В статье приводится анализ особенностей существующих конструкций дискретизирующего барабанчика прядильной машины. Представлена конструктивная схема и принцип работы рекомендуемого составного дискретизирующего барабанчика с амортизатором и секционными зубчатыми гарнитурами. Результаты теоретических исследований вертикальных колебаний секционных зубчатых гарнитур дискретизирующего барабанчика. На основе полученных закономерности колебаний зубчатых гарнитур и построенных графических завимостей обоснованы основных параметры барабанчика.

Ключевые слова: Прядильная машина, дискретизирующый барабанчик, волокна, лента, зубчатая гарнитура, амортизатор, масса, жесткость, диссипация, колебания, амплитуда, размах, частота.

INTRODUCTION

The essence of the discretization process lies in separating the tape into separate non-contacting fibers, in relative displacement and in distributing them over a very large length. In the process of discretization, an extra-high thinning occurs, i.e. the tape is thinned by 30007500 times, and in the section of the discrete flow with ideal separation there are 2-6 non-contacting fibers. This is the difference between sampling and pulling. [1] Discretization is carried out in order to form a discrete flow of non-contacting fibers, which cannot perceive and transmit torque due to the rotation of the forming - twisting device - spinning chamber, thereby creating conditions under which no false twisting occurs between the sampling device and the outlet pair. The discretization process is carried out in a discretizing device. At present, the design of the device of the BD-200 type machine is most widely used.

In another well-known design, the receiving drum assembly of the Maxilin type [2] is made of a steel pipe with an eight-start wave groove. The analyzes show that during single-start winding of the headset, the beard in this area is exposed to the tooth once per revolution of the drum. And during this period, it is possible to supply such a quantity of tape that the knot of the

UIF-2022: 8.2 ISSN: 2181-3337

SCIENCE AND INNOVATION 2022

INTERNATIONAL SCIENTIFIC JOURNAL

strand of fibers will be entirely fed into the working area and remain uncombed and turn into yarn. This certainly applies to a number of inclusion sizes commensurate with the feed per drum revolution, or less than it. Larger groups of fibers will be processed by the sampling roller.

The disadvantage of the discretizing drum is: the low effect of the separation of weed impurities from the fiber, as well as the insufficient uniformity of the division of the fiber mass into individual fibers, especially with different fiber lengths.

MATERIALS AND METHODS

Efficient sampling drum design. A design of a composite sampling drum was developed, the scheme of which is shown in Fig.1. [3].

Fig 1 Discretizing drum of an rotor spinning machine

The structure works in the following way. When the discretizing drum rotates and due to the impact of the technological load from the fibers, the outer sleeve 1 with a toothed 2 or needle 3 headset perform additional high-frequency torsional vibrations due to their installation on the base 4 by means of an elastic (rubber) sleeve 5. By choosing the required rigidity of the elastic sleeve 5, one can obtain torsional vibrations with a certain amplitude and frequency, at which the efficiency of fiber separation from the main mass increases due to additional inertial forces. At the same time, fiber breakage is significantly reduced. The feed tape with a height of 2.0 mm and a width of 9.0 mm has the highest density in its middle [3.4].

At the same time, due to the increased friction of the fibers along the side walls of the base 4 and the cover 7, the fibers remain from the main fibrous mass. Making the height of the teeth 2 and needles 3 installed along the edges of the drum greater by 0.4^0.6 mm than the height of the teeth 2 and needles 3 along its middle allows overcoming the friction of the resistance of the fibers against the side surfaces, which increases the uniformity of movement and discretization of the fibers throughout drum width. To ensure efficient discretization of a

tape of artificial fibers, the outer sleeves 1 with a toothed headset 2 are replaced by outer sleeves 1 with a needle-like headset 3.

When discretizing a tape consisting of a mixture of natural and artificial fibers, you can use the outer sleeve 1 of the toothed 2 and needle 3 headsets installed in alternation. Therefore, the proposed design is universal.

The proposed device allows increasing the efficiency and uniformity of discretization of fibrous material.

RESULTS

Calculation scheme and mathematical model of vertical oscillations of the gear set of

the drum. The parts of the discrete drum gear headsets are the same size. Therefore, their calculation schemes will be the same. The general calculation scheme is shown in Figure 2.

Lagrange's II-order equation [5,6] was used to generate the differential equation representing the oscillations of the gear set:

d_ dt

Here, qi,Q(qt)— generalized coordinates and generalized forces, T, P - kinetic and potential energies; F is the dissipative function of the relay [7,8].

(dr^

a//

_dL+dn + dn =Qm

Ôqi Ôqi dqi

(1)

Figure 2. Calculation diagram representing the vertical vibrations of the gear set of the

discrete drum

According to the calculation scheme, the potential, kinetic energies and dissipative function of the gear headset parts are determined from the following expressions: [5,8]:

1 -

P = - cy ' 2

t -

1 =— m ;

2 g'

F = - vf dy

2 { dt,

(2)

here, c,v are the coefficients of virginity and dissipation on the linear deformation of the rubber bushing under the headset parts; y - vertical shift; mass of mg-toothed headset part;

From the obtained expressions (2) were obtained products on the generalized coordinate

[9,10]:

ai

ap ÔF dy

— = cy ; — = v — ;

Ôy Ôy dt

The yields over time are as follows [9]:

dy dt

ay

Ôi

mgy;

= m =

Ôi=0

Ôy

d 2 y dt2

(3)

2

Generalized power [9];

F = F + F sin ct ±SF„

r-o-......-1 (4)

By placing the obtained (3), (2) on (1), a differential equation was formed that represents the vertical oscillations of the gear set of the discrete drum [10,11];

m^ + cy + v— = F + F sinct ±SF J fit 1 1

ig

g i 2 —t2

(5)

The resulting (5) solution, which represents the free oscillations of the gear headset parts, is as follows [71,72];

y = (e sin^i + £2 cos^j (6)

here c0 =yj p0 - n ; p0 =

c т

n = ■

2m

The current solution for variant F = 0^ ÔF^ = 0 is the following expression for the forced oscillations according to [12]:

F0 sin

y = -

ct - arctg

f 2nc ^

2 2

^ P0 -C )

(p0 -c2 j2 + 4^-C2

(7)

But the general solution of (5) was carried out on a computer using a random number generator, based on the Runge-Kutta program.

DISCUSSION

Analysis of the wobbling of the parameters of the discretizing drum on the nature of its vibrations. The expressive numerical solution (7) generated to obtain the oscillation laws of the discrete drum gear sets was performed separately for each gear set. Calculations were performed at the following values of the parameters:

m = (1,2 -1,8)-10" 2 kg; nd =(6.0 - 7.5)-10" 3rev per min;

F =(12 - 24)sN; Fq = (2,3 - 4,5)sN; F = (0,25 - 0,65)sN;

c = (0,08 - 0,35) -103 N / m; v = (1,3 - 2,5)Nc / m; |

Yi y3

vit&stit&e^^

t

0.4-10"3.w

0.5 10"-V

iНе можете найти то, что вам нужно? Попробуйте сервис подбора литературы.

l-

-

y2

Fn =(12 + 2.3sinct ± 0.25>N; c = 0.25-103 N/m; h = 6. 103 rev per min; v = 2,5 Ns/m;

a

> t

B

г

a

F = (18 + 3.35smfflT ± 0.45)cH; c = 0.25 -103 N/m;

n = 6 • 103 rev per min; e = 2,1 Ns/m; d

F = (24 + 4.35sin®/ ± 0.65)sN; c = 0.25 -103 N/m; n = 6 • 103 rev per min; e = 2,1 Ns/m;

Figure 3. The laws of vertical and vibration dependence of the laws of vertical vibration of discrete drum gear sets with the proposed composition are given.

In the obtained laws, the laws of vertical displacement of each of the three gear sets of the discrete drum are defined separately (Fig. 3, Yi, Y2, Y3, graphs). The figure shows the dependence of the proposed composition of the discretization of the drums on the technological laws of vertical vibration of the gear sets and the frequency of rotation of the drive. According to the analysis of the obtained laws, it was found that the amplitude of vibration of the gear set in the middle of the discrete drum is higher than (15 ^ 20)% when the amplitude of vibration of the end gear set. The main reason for this is that it is taken as F' = 1,2Fj = 1.2F3, i.e. due to the

magnitude of the technological resistance acting on the middle gear set.

This is because the density of the tape fibers in the middle zone is higher. It should be noted that the vibration amplitudes of Yi, Y2, and Y3, also depend on the linear virginity coefficients of the rubber bushings on which the headsets are mounted. It can be seen from the laws in Figure 3 that as the technological resistance increases, the vibration amplitudes of the gear sets also increase accordingly (Figures 3, a, b, v-graphs). Their oscillation frequencies are almost equal to the rotational frequency of the drive during steady motion. In this case, the value

of the oscillation frequency is

1.22-102 Gts. Correspondingly, when the drive speed was

increased to

7.5-10J

rpm, the vibration frequencies of the gear sets increased proportionally and became equal to 1.42-102

Gts (Fig. 4, graphs a, b, v). In this case, the effect of the values of the vibration amplitudes of all three gear sets of the discrete drum is almost unchanged.

As a result of processing the obtained laws, graphs of the dependence of the vertical vibration coverage of gear sets on their parameters were constructed. Figure 5 shows graphs of the oscillation coverage of the discrete drum gear heads depending on the drive rotation frequency.

Analysis of these coupling graphs showed that when the rotational speed of the drive increases from 4.5-103 rpm to 7.2-103 rpm, the vibration coverage of the two edge gears increases linearly from 0.130-10-3 m to 0.615-10-3 m at values Ay and Ay

F =(12 + 2.3sin(t ±0.25) sN, where Ay and Ay. The laws of change are almost the same, except that the oscillation phases shift.

t . yj j^y

t

0.410_J.V

0.5 10" V

vwwwwA/vmmw

Fn =(12 + 3.35sin(t ± 0.25)sN; c = 0.25 -103 N/m;

t

n

= 7.5 • 103 rev per min; v = 2,1 Ns/m;

Fn =(18 + 3.35sin(t ± 0.45)sN; c = 0.25 -103 N/m;

n

= 7.5 • 103 rev per min; v = 2,1 Ns/m;

Fn =(24 + 4.55 sin (t ± 0.6)s#; c = 0.25-103 N/m; n = 7.5-103 rev per min; V = 2,1

Ns/m;

Figure 4. The dependence of the laws of vertical vibration of the discrete drum gear sets of the proposed composition on the technological and drive frequency is given.

But the vibration coverage of the gear set in the middle will be greater than the vibration coverage values for the F2 = 12 • F pieces. Correspondingly, the values of Ay = Ay increase

in a nonlinear pattern from 0.485 • 10" m to 1.42 40"3 m. It should be noted that when the coverage values of the oscillations of the middle gear set are F =0-2 + 2.3sin ct±0.25)sN,

respectively, the values of A^ increase in a nonlinear pattern from 0.13840"3 m to

0.79 40" 3 m.

When the technological resistance F1=24,0 sN, the values of A^ increase from 0.54 • 103 m to 1.62 • 10-3 m. According to the results of experimental studies, the selection of the drive speed in the range of 10-3 rpm (7,0 ^ 7,5) to ensure that the vertical vibrations of the gear headset, as well as the difference between the teeth of the headset does not exceed (1,0 ^ 1,2) • 103 m expedient. However, it is possible to increase the values of pd to (10 ^ 12)• 103 rpm by selecting the appropriate values of shock absorber virginity.

1,2,3-A^ =Ay3 = f(nd) 4,5,6-Ay = f(nd) 1,4-Fn =(12+2.3sinœt±0.25)sN;

2,5 - F =(18 + 2.35 - sin œt ± 0.45) sN; 3,6 - F =(24 + 4.3sinœt ± 0.65) sN;

Figure 5. Graphs of the frequency dependence of the oscillation coverage of the discretion

drum gear sets

1.3-I, III-section gear headset zones; 2-4-II- middle section gear headset zone;

1,2 " Fn = (12 + 2.3sin cot ± 0.25)sN; 3,4 - Fn = (18 + 2.35 - sin cot ± 0.45)sN;

= 6 • 103 rev per min.

Figure 6. Graphs of the dependence of the vibration coverage of discrete drum gear sets on the coefficient of virginity of the rubber shock absorber

Figure 6 shows graphs of the dependence of the vibration coverage of discrete drum gear sets on the rubber shock absorber coefficient. According to the analysis of graphs, when the shock absorber height increases from 0,65• 103 N/m to 0,35• 103 N/m and F1=12,0 cH, Ay = Ay values decrease from 0.62 • 10-3m to 0.132 • 10-3 m, respectively F1=18,0 sN, the

values of Ay =Ay decrease in a linear pattern from 0.93 • 10-3 m to 0.26-10-3 m (Fig. 2.5, Figures 1.3).

Gear headset parts

1,4 - F =(24 + 4.5sinct ± 0.65) cH; 2,5 - F = (18 + 3.35 - sinct ± 0.45)sN;

3,6 - FM =(12 + 2.3sin ct ± 0.25) cH; 1,2,3 - = 7.5 •lO3 rev per min; c = 0.12 403 N/m; 6 = 1.3 Hc/m; 4,5,6 - ^ = 6.0 403 rev per min; c = 0.25 403 N/m; 6 = 2.1 Ns/m;

The vibration coverage of the middle gear headset decreases from 1,28 403m to

0,43 40 3 m when F1=12,0 sN. It can also be seen that when F1=18,0 sN, the values of Ay

decrease in a nonlinear bond from 1,21403 m to 0,5140 3 m. It is therefore advisable to obtain

the virulence values of the generalized shock absorber greater than (0,2^0,35)40-3 N/m to

ensure that the values of Ay, Ay and Ay are in the range of (1,0 -1,2)^10-3 m.

The analysis of the graphs shows that the coverage of vertical vibrations of the gear set in the middle zone can be seen as the technological resistance and the magnitude of the vibration coverage of the gears on both sides increase with increasing drive speed. However, it is possible to equalize the values of Ay, Ay and Ay by installing a separate shock absorber for each

gear set and installing rubber bushings in the corresponding brackets.

Therefore, it is recommended to obtain a rubber bushing coefficient of virginity in the range of (0.18 ^ 0.20)403 H/m for the shock absorbers of the two end gears and (0.32 ^ 0.35 )• 103 H/m for the shock absorbers of the average gear headset.

UIF-2022: 8.2 SCIENCE AND INNOVATION 2022

ISSN: 2181-3337 INTERNATIONAL SCIENTIFIC JOURNAL №4

CONCLUSIONS

An effective structural scheme of a composite sampling drum has been developed. On the

basis of theoretical studies, the laws of vertical vibrations of the gear sets of the drum are

obtained, and its parameters are substantiated.

REFERENCES

1. G.I. Magauzov, K.V. Sergeev. Device and maintenance of pneumomechanical spinning machines. Moscow, Legprombytizdat., 1985, 58-61 p.

2. S.L. Matismailov. Improving the processing of fine-staple cotton in the knot of the carding drum. Candidate's abstract. diss., Leningrad, 1989, 23 p.

3. Patent UZ No. IAP 06730. Discretizing drum of a pneumatic spinning machine / Juraev A.J. Urakov N.A., Mirzaev O.A., Akhmedov K.I. // Official Newsletter. -2022. -No. 6.

4. Juraev A.J., Urakov N.A., Mirzaev O.A., Almardonov O.M., Usmanov Kh.S. Analysis of the loading of the feed cylinder in the power unit of spinning machines // Moscow. Universum: Engineering science magazine №3 2021, bet /49-53

5. Panovko Ya.G. Fundamentals of the applied theory of oscillations and impact, Mechanical engineering, L., 1976, 320 p.

6. Timoshenko S.P., Young D.H., Unver U., Fluctuations in engineering. Engineering, M., 1976, 320 p.

7. Den-Gartog D.P. Mechanical vibrations. M.: Fizmatgiz, 1960.-580 p.

8. Mansurova M A 2016 Influence of parameters of elastic elements on vibrations of a lever with a rack in a sewing machine Scientific and technical journal of Fer PI 20(1) pp 41-5.

9. Mansurova M A, Tajibaev Z and Tashpulatov S 2009 Tension of the upper thread for a highly elastic two-thread chain stitch Problems of textiles -Tashkent 4 pp 87-90.

10. Yunusov S Z, Khaidarov A and Bobomurodov T G 2013 Machine unit with the mechanism of a composite cylinder of technological machines Theory of machines and working processes MNPK 2013 pp 26-7.

11. Mamakhanov A A 2021 Development of structures and calculation methods for chain drives with elastic elements of technological machines (Namangan: Dissertation (DSc) in technical sciences) 2021.

12. Mansurova M A, Madrakhimov Sh and Umarova Z M 2016 Analysis of the influence of the lengths of the coupler and rocker arm links on the position of the flat four-link mechanism Theory of mechanisms and machines 14 l (2) pp 21-9.

i Надоели баннеры? Вы всегда можете отключить рекламу.