Научная статья на тему 'Development of a multilayered hybrid power divider'

Development of a multilayered hybrid power divider Текст научной статьи по специальности «Электротехника, электронная техника, информационные технологии»

CC BY
75
16
i Надоели баннеры? Вы всегда можете отключить рекламу.
Ключевые слова
MICROWAVE MODULES / WEIGHT AND SIZE CHARACTERISTICS / MULTILAYER TECHNOLOGY / HYBRID RING / SLOT LINE / СВЧ-МОДУЛИ / МАССОГАБАРИТНЫЕ ХАРАКТЕРИСТИКИ / МНОГОСЛОЙНАЯ ТЕХНОЛОГИЯ / ГИБРИДНОЕ КОЛЬЦО / ЩЕЛЕВАЯ ЛИНИЯ

Аннотация научной статьи по электротехнике, электронной технике, информационным технологиям, автор научной работы — Dudarev N.V., Darovskih S.N.

The paper proves a real possibility of designing the microwave electronic devices based on multilayer structures. The advantages of such design compared with a traditional application of the microstrip lines are demonstrated by an example of a hybrid microwave power divider (hybrid ring). The calculations of a multistructure-based hybrid ring presented in the paper allow forecasting a substantial decrease of the weight and size parameters for the microwave electronic devices. That provides their wide application in mobile and small-sized radio systems with a microwave informational channel. The weight and size problem is especially relevant for the devices like the various mobile on-board radars. This makes it possible to predict scientific and industrial relevance of the development.

i Надоели баннеры? Вы всегда можете отключить рекламу.
iНе можете найти то, что вам нужно? Попробуйте сервис подбора литературы.
i Надоели баннеры? Вы всегда можете отключить рекламу.

Текст научной работы на тему «Development of a multilayered hybrid power divider»

Инфокоммуникационные технологии и системы

DOI: 10.14529/ctcr170104

DEVELOPMENT OF A MULTILAYERED HYBRID POWER DIVIDER

N.V. Dudarev, [email protected],

S.N. Darovskih, [email protected]

South Ural State University, Chelyabinsk, Russian Federation

The paper proves a real possibility of designing the microwave electronic devices based on multilayer structures. The advantages of such design compared with a traditional application of the microstrip lines are demonstrated by an example of a hybrid microwave power divider (hybrid ring). The calculations of a multistructure-based hybrid ring presented in the paper allow forecasting a substantial decrease of the weight and size parameters for the microwave electronic devices. That provides their wide application in mobile and small-sized radio systems with a microwave informational channel. The weight and size problem is especially relevant for the devices like the various mobile on-board radars. This makes it possible to predict scientific and industrial relevance of the development.

Keywords: microwave modules, weight and size characteristics, multilayer technology, hybrid ring, slot line.

Introduction

A variety of the modular microwave devices such as couplers, bridge circuits, and matched dividers are widely used in a microwave equipment to control a signal in a microwave path. The major drawback of these devices is the directly proportional relationship of their weight and size characteristics and a working frequency range. While the mass-dimensional characteristics are not very significant for the stationary objects such as terrestrial radar systems, the weight and size savings become vital for microwave devices set on the mobile objects. Consequently, the development a microwave technology targeting to the weight and size decrease is a topical problem. Nowadays solutions are based on the microstrip technology, which applies the methods of magnetic sputtering, hybrid hook-up elements, and dielectrics with high relative dielectric constants [1]. However, the potential of the technology in decreasing the weight and size characteristics of microwave devices is limited by their single-layer architecture. Therefore, it seems appropriate to consider developing microwave electronic devices based on their multilayer structure.

Let us estimate the advantages of the devices developed with the use of multilayer technology considering an example of microwave power divider (hybrid ring). Its weight-size and electric characteristics compared with those of a device traditionally designed by microstrip technology would allow the conclusion that the multilayer technology is advanced to develop the microwave electronic devices.

1. Design of a microwave divider based on a microstrip technology

A bridge circuit of the microwave power divider (hybrid ring) (Fig. 1) in its traditional single-layer performance is widespread in the microwave radiotechnical systems.

Its calculation [2, 3] reduces to determining a mean diameter dmean and ring width Wk at the known values of a microstrip line width W, wave resistance Z0, effective dielectric permeability sef, main transmission line (1-4), operation frequency (wave-length A0), and other benchmark data and requirements applicable to the power divider. The basic relations for calculating the parameters of a hybrid ring are the following [2-5]:

d = 3A° (1)

Umean inJITf (1)

where eef is an effective dielectric permittivity. For a microstrip line, it is calculated using a formula

Í1+KY~2, (2)

_Sr + l ,£r-l,

£ef _--+ '

where sr is a relative dielectric permittivity of the dielectric base, W is a width of a microstrip line, and h is a thickness of the dielectric.

W _ h

W„_ h

ZoV^r 200(1-f) !

ZfcV^

(3)

(4)

where A is a metallization thickness, Z0 is an input wave resistance, and Zk is a wave resistance of the ring.

Zfc = Z0V2. (5)

Fig. 1. Hybrid ring

When using the formulas (1)-(5), the values of the hybrid ring parameters such as dmean = 45 mm and Wk = 1.7 mm were obtained for the following conditions: frequency range was 945-970 MHz, the width of a microstrip line W = 3.52 mm, the input wave resistance Z0 = 50 Ohm, and the base material was double-sided laminated dielectric R04003.

To evaluate a correspondence between electromagnetic characteristics of the calculated hybrid ring (Fig. 2) and those specified for an even division of a signal power (-3 dB), reflection factor and electromagnetic decoupling not less than 20 dB in the range 945-970 MHz, the user's CAD system CST Microwave Studio was utilized.

Fig. 2. Single-layer topology of a hybrid ring model

As a result of calculations using CAD, the electromagnetic characteristics of the device has been obtained. The diagrams of the scattering matrix elements are the most illustrative (Fig. 3). Analysis of

the diagrams really gives exhaustive information we need to know about the electrical characteristics of microwave modules in design engineering. On the ground of calculation of the main electromagnetic characteristics for the hybrid ring with the mentioned parameters (Fig. 3), the following conclusions could be done in accordance with the scattering matrix graphs.

• The device provides an even division of the channel 1 signal power by the channels 3 and 4 (S31, S4i = -3 dB) in a broad band (950-1000 MHz).

• Decoupling in the same band varies from -25 dB on the band edges to -40 in its centre.

• The reflection factor (S11) in the band 950-1000 MHz varies from -25 dB on the band edges to -32 in the centre.

S-Parameter [Magntude in dB]

200 400 600 600 967.07 [>00 1200 1400 1600

Frequency / MHz

Fig. 3. Amplitude characteristics of the hybrid ring by the microstrip technology, where S31 and S41 are the power dividing coefficients, S21 is a decoupling factor between 1 and 2 inputs of the device, and S11 is a first input

reflection factor

The characteristics show that the device can operate not only in the frequency band 945-965 MHz predetermined when calculating but also in the much wider band 950-1000 MHz with keeping all the main requirements to the device such as even division of the signal power by the channels (S31, S41 = -3 dB), the value of decoupling, and reflection factor not less than -20 dB.

In addition, the size 100 x 70 x 1.52 mm of device specifies its volume equal to 10 640 mm3 (excluding the shielding case). A width of air space from a transmission line to a metal shield should be not less than three widths of a dielectric for the microstrip line. Consequently, the real volume of the product in case is 42 560 mm3 (10 640 x 4 mm3).

2. Multilayered hybrid ring

To implement the hybrid ring based on the multilayer structure, the overall size calculated above are used. In a space of decoupled input arms, the divider is decomposed into two parts and placed on several dielectrics (Fig. 4). Two clad dielectrics R04003 are used. The dielectrics fit together and each half of divider is placed on the outside. Metallization between two dielectrics acts as a shield. The openings for the jumpers connecting the parts of the hybrid ring are etched in the shield (Fig. 4).

Fig. 4. A model of themultilayered divider with the jumpers. 1 and 2 are the transmission lines, 3 is via opening,

and 4 is a jumper

It follows from the calculation of the main characteristics of the multilayered hybrid ring (Fig. 5) that the multilayered power divider matches its single-layered analogue in amplitude characteristics while it is approximately 6 times more compact (size is 40 x 40 x 4.56 mm (7296 mm3)). As the device is implemented on the symmetrical line, the shielding case is situated back-to-back with the product (an impact of the case on the total volume of a product is neglectable).

S-Parameter [Magnitude in dB]

-45 -i-i-i-i ' -i-i-i-i-i-

500 600 700 800 900| 929.541 1000 1100 1200 1300 1400 1500

Frequency / MHz

Fig. 5. Amplitude characteristics of the multilayered hybrid ring depending on a frequency

A shortcoming of such hybrid ring is existence of the openings. The shortcoming may be viewed in different ways such as technological and electrodynamical ones. In terms of technology, the openings imply the whole range of additional operations. Naturally, the openings are not an unsolvable problem. Today the process of obtaining the via openings is mastered and applied successfully to produce the low-frequency cards. In terms of thermodynamics, a jumper is a specific kind of transmission line (waveguide), so it should have a wave resistance about 50 Ohm. The layers may be connected by a slot line (Fig. 6).

Fig. 6. A model of a volume slot line. 1 and 2 are coupled regions (slots), 3 and 4 are transmission lines

Instead of a jumper, in the hybrid ring it is possible to use a volume slot line, which consists of two metalized zones on opposite sides of a clad dielectric. Depending on the overlap value, it is possible to obtain a slot line with definite wave resistance.

Analysis of the calculation results for the amplitude characteristics of a volume slotted junction (Fig. 7) allows for the conclusion that the junction could be used in low-band devices permitting the signal bandwidth, which does not exceed 10 % of the carrier frequency value. The key feature of a slot line is its length, which should be equal to a quarter or one eighth part of the wavelength. For space saving, the slot lines are assembled in meander structures and their transit characteristics are compared with those of the previous model (Fig. 8 and 9).

S-Parameter [Magnitude in dB]

51,1 : -33.490487 52.1 : -0.30356599 51.2 : -0.31415443 S2,2 : -31.798792

Frequency / MHz

Fig. 7. Amplitude characteristics of a volume slotted junction

S-Parameter [Magnitude in dB]

a)

Frequency / MHz b)

942.39 10»

51Д : -31.410661 52.1 : -0.47392913 51.2 : -0.18823566 S2,2 : -36.257371 :----

Fig. 8. A model of a volume slotted junction assembled in a periodical meander structure (a), and its amplitude

characteristics (b)

Fig. 9. A model of a volume slotted junction with a complex structure (a), and its amplitude characteristics (b)

Being compared, the amplitude characteristics of the junctions (Fig. 7-9) demonstrate that while the number of the spot line creases grows, a marginal deterioration of the reflection factor and inconspicuous decrease of a routing signal value takes place.

A model of a hybrid ring implementation based on an elementary slot line without creases is presented in Fig. 10.

The hybrid ring has the overall size 70 x 50 x 3.04 mm (10 640 mm3).

A design process for each of the devices described above was performed in accordance with the following algorithm presented as a flow chart (Fig. 11).

a) b)

Fig. 10. A model of a hybrid ring with volume slot lines (a) and its amplitude characteristics (b)

Fig. 11. A flow chart of a process algorithm for designing the microwave electronic devices

Conclusion

The paper introduces the multilayer technology to implement the microwave electronic devices such as directional couplers, phase shifters, filters, various power dividers, and combiners, etc. The application of the technology allows making a real progress in achieving weight-size minimum. It has been demonstrated by the example of the hybrid ring implemented in both traditional microstrip and multi-layered constructs. With equal level of the electrical characteristics, the multilayered hybrid divider has a volume 6 times less than the microstrip one.

A significant advantage of the technology is a feasibility of a high packing density for the complex radiotechnical devices using the microwave electronic components.

References

1. Maloratsky L.G. Mikrominiatyurizatsiya elementov iustroystv SVCH [Microminiaturization of Microwave Elements and Devices]. Moscow, Sov. Radio Publ., 1976. 216 p.

2. Bakharev S.I., Volman V.I. (ed.), Lib Yu.N. Spravochnikpo raschetu i konstruirovaniyu SVCH poloskovykh ustroystv [Handbook on Calculation and Design of Microwave Microstrip Devices]. Moscow, Radio i Svyaz, 1982. 328 p.

3. Maloratsky L.G., Yavitch L.R. Proektirovaniye i raschyot SVCH elementov na poloskovykh liniyakh [Design and Calculation of Microwave Microstrip Elements]. Moscow, Sov. Radio Publ., 1972. 232 p.

4. GOST 21702-76. Ustroistva SVCH. Poloskovye linii [Microwave Devices. Microstrips]. Moscow, Standart Publ. House, 1977. 4 p.

5. Felstein A.L., Yavitch L.R. Sintez chetyrekhpolyusnikhov i vos'mipolyusnikhov na SVCH [The Synthesis of Microwave Quadrupoles and Octupoles]. Moscow, Svyaz Publ., 1971. 385 p.

Received 5 September 2016

УДК 621.372 DOI: 10.14529/^сг170104

РАЗРАБОТКА ГИБРИДНОГО ДЕЛИТЕЛЯ МОЩНОСТИ НА МНОГОСЛОЙНОЙ СТРУКТУРЕ

Н.В. Дударев, С.Н. Даровских

Южно-Уральский государственный университет, г. Челябинск

В статье доказывается реальная возможность проектирования устройств сверхвысокочастотной (СВЧ) электроники на основе многослойной структуры их построения. На примере гибридного СВЧ-делителя мощности (гибридного кольца) показаны преимущества такого проектирования в сравнении с традиционными подходами, основанными на использовании микрополосковых линий. Приведенные в статье расчеты гибридного кольца на основе многослойной структуры позволяют сделать прогноз о существенном уменьшении массогабарит-ных характеристик устройств СВЧ-электроники, что обеспечивает возможность для их широкого использования в мобильных и малоразмерных радиотехнических системах с СВЧ каналом передачи и приема информации. Особенно актуальна проблема массогабаритных характеристик для таких устройств, как бортовые радиолокационные станции различного рода подвижных объектов. Это позволяет прогнозировать научную и производственную актуальность данной разработки.

Ключевые слова: СВЧ-модули, массогабаритные характеристики, многослойная технология, гибридное кольцо, щелевая линия.

Литература

1. Малорацкий, Л.Г. Микроминиатюризация элементов и устройств СВЧ/Л.Г. Малорацкий. -М. : Сов. радио, 1976. - 216 с.

2. Справочник по расчету и конструированию СВЧполосковых устройств: справ. / С.И. Ба-харев, В.И. Вольман, Ю.Н. Либ; под ред. В.И. Вольмана. - М. : Радио и связь, 1982. - 328 с.

3. Малорацкий, Л.Г. Проектирование и расчет СВЧ элементов на полосковых линиях / Л.Г. Малорацкий, Л.Р. Явич. - М. : Сов. радио, 1972. - 232 с.

4. ГОСТ21702-76. Устройства СВЧ. Полосковые линии. -М: Изд-во стандартов, 1977. - 4 с.

5. Фельштейн, А.Л. Синтез четырехполюсников и восьмиполюсников на СВЧ/ А.Л. Фельд-штейн, Л.Р. Явич. - 2-е изд. -М. : Связь, 1971. - 385 с.

Дударев Николай Валерьевич, аспирант кафедры инфокоммуникационных технологий, Южно-Уральский государственный университет, г. Челябинск; [email protected].

iНе можете найти то, что вам нужно? Попробуйте сервис подбора литературы.

Даровских Станислав Никифорович, д-р техн. наук, заведующий кафедрой инфоком-муникационных технологий, Южно-Уральский государственный университет, г. Челябинск; darovskih. s @тай. ги.

Поступила в редакцию 5 сентября 2016 г.

ОБРАЗЕЦ ЦИТИРОВАНИЯ

FOR CITATION

Dudarev, N.V. Development of a Multilayered Hybrid Power Divider / N.V. Dudarev, S.N. Darovskih // Вестник ЮУрГУ. Серия «Компьютерные технологии, управление, радиоэлектроника». - 2017. - Т. 17, № 1. -С. 34-41. DOI: 10.14529/ctcr170104

Dudarev N.V., Darovskih S.N. Development of a Multilayered Hybrid Power Divider. Bulletin of the South Ural State University. Ser. Computer Technologies, Automatic Control, Radio Electronics, 2017, vol. 17, no. 1, pp. 34-41. DOI: 10.14529/ctcr170104

i Надоели баннеры? Вы всегда можете отключить рекламу.